How Many Amps Does a 15 HP three-phase Motor Draw at 208V?

At 208V, 15 horsepower equals roughly 42.99 amps per line of running current on a three-phase circuit. One HP is 746 watts of mechanical output, but motors are not 100% efficient, so the electrical draw is higher. Applying √3 × V_L-L × Eff × PF: 11,190W ÷ (√3 × 208 × 0.85 × 0.85) = 11,190 ÷ 260.29 = 42.99 A.

15 HP three-phase motor at 208V

42.99 Amps per line running

Calculated running current at the motor terminals at the assumed 85% efficiency and PF 0.85, per line on a balanced three-phase circuit. This is a conversion from the nameplate horsepower using those assumptions, not a measured value; a real meter reading depends on the motor's actual nameplate efficiency, loading, temperature, and motor design.

NEC Table 430.250 FLC (code sizing base)46.2 A

Conductor min ampacity (NEC 430.22, 125% of FLC)57.75 A

Electrical input (HP × 746 ÷ efficiency)13,164.71 W

Try: 15HP at 208V (3Φ) 10HP at 208V (3Φ) 20HP at 208V (3Φ) 7.5HP at 208V (3Φ)

Volts

Motor Type

Running Amps (per line)

42.99

NEC Table 430.250 FLC (code sizing)

46.2

Use the running amps for metering and energy calculations. For branch-circuit sizing, AC motors use the NEC Table 430.248 / 430.250 full-load current under NEC 430.6(A)(1); DC motors use the motor nameplate full-load current under NEC 430.6(A)(3), with Table 430.247 as the reference. Three-phase current is shown per line on a balanced circuit.

Formula (three-phase)

I_(A) = (HP × 746) ÷ (√3 × V_L-L × Eff × PF)

(15 × 746) ÷ (√3 × 208 × 0.85 × 0.85) = 11,190 ÷ 260.29 = 42.99 A per line

Convert HP to watts: 15 × 746 = 11,190W
Denominator: √3 × 208 × 0.85 × 0.85 = 1.73 × 208 × 0.85 × 0.85 = 260.29
Result: 11,190 ÷ 260.29 = 42.99 amps per line

Three-phase current is per line on a balanced circuit. Voltage is line-to-line; the √3 factor comes from the three-phase vector geometry, not a round-trip doubling.

NEC Reference Values

This section lists the Code reference numbers a motor branch circuit is sized from. Final conductor, breaker, disconnect, and overload selection is an install decision a licensed electrician makes against the motor nameplate, the actual install conditions, and the applicable NEC articles, not a decision a conversion page can make for you.

NEC Sizing Base: NEC Table 430.250 FLC

Per NEC 430.6(A)(1), motor branch-circuit conductors, switches, and overcurrent protection are sized from the values in Table 430.248 (single-phase) or Table 430.250 (three-phase), not from the motor nameplate and not from a calculated full-load amps. For a 15 HP three-phase motor at 208V, the table value is 46.2 A (direct column match under 430.6(A)(1)).

The 42.99 A shown in the hero is the calculated running current at 85% efficiency and PF 0.85, per line on a balanced three-phase circuit. This is a conversion from the nameplate horsepower under those assumptions, not a measured value; a real meter reading depends on the motor's actual efficiency, loading, temperature, and design. Use this figure for energy and metering estimates, and use 46.2 A as the reference FLC when an electrician walks through NEC 430 against the nameplate.

NEC 430.22 Conductor Rule (reference formula)

NEC 430.22 requires motor branch-circuit conductor ampacity of at least 125% of the Code sizing FLC. As a reference calculation against the NEC Table 430.250 value: 46.2 × 1.25 = 57.75 A. The selected conductor is taken from NEC Table 310.16 at the applicable termination temperature column, with ambient, bundling, and cable-type adjustments applied by the installer. Motor branch-circuit conductors are exempt from the 240.4(D) small-conductor rule via 240.4(G).

NEC 430.52 Overcurrent Protection (code caps)

NEC Table 430.52(C)(1) gives the maximum rating for motor short-circuit and ground-fault protection as a percentage of the Code sizing FLC. The percentage depends on the device type:

Device Type	Maximum % of Table FLC (430.52(C)(1))
Non-time-delay fuse	300%
Dual-element (time-delay) fuse	175%
Inverse-time circuit breaker	250%
Instantaneous-trip circuit breaker	800%

These percentages are maximum caps, not install picks. A real circuit applies the percentage against the Code sizing FLC for the specific device type, rounds up to a standard size per 430.52(C)(1)(a), and is verified against the motor nameplate and the install conditions by the installer. The elevated percentages exist so short-circuit protection does not nuisance-trip on locked-rotor startup inrush.

Locked Rotor (Startup) Current

During the first 2-5 seconds of startup, a squirrel-cage induction motor typically draws 5 to 7 times the NEC Table 430.250 FLC of 46.2 A (roughly 231 to 323.4 A). This is why the 430.52(C)(1) percentages above are so much higher than running current: the short-circuit/ground-fault protective device has to ride through locked-rotor inrush without tripping. Actual LRA is set by the motor's NEMA code letter on the nameplate and should be checked there for a real install.

Current	Amps	Duration
Calculated running current (meter)	42.99 A per line	Continuous at full load
NEC Table 430.250 FLC (Code reference)	46.2 A	Sizing base, not metered
Locked rotor (typical, 5-7×)	231-323.4 A	2-5 seconds

Operating Cost

Motor mechanical output is 11,190 W (15 HP × 746). Electrical input at the terminals is higher because no motor is 100% efficient: 11,190 ÷ 0.85 = 13,164.71 W. At $0.17/kWh, running cost is $2.24/hour or $537.12/month at 8 hours/day. Full breakdown at 13,164.71 W.

Amps by Motor Efficiency (three-phase)

Motor efficiency directly affects amp draw. A more efficient motor draws less current for the same HP output. Values below are the calculated three-phase running current at 208V per line and PF 0.85:

Efficiency	Amps at 208V (per line)	Watts Consumed	Waste Heat
75%	48.72 A	14,920 W	3,730 W
80%	45.68 A	13,987.5 W	2,797.5 W
85%	42.99 A	13,164.71 W	1,974.71 W
90%	40.6 A	12,433.33 W	1,243.33 W
95%	38.46 A	11,778.95 W	588.95 W

Other HP Values at 208V (three-phase)

Running current is the calculated three-phase draw per line at 85% efficiency and 0.85 PF (a conversion from HP under those assumptions, not a measured value). NEC Table FLC is the value from NEC Table 430.250 used for branch-circuit conductor and OCP sizing under NEC 430.6(A)(1). LRA is estimated at 5-7× the NEC table FLC; rows outside the table show n/a because there is no code-authoritative LRA basis for that HP/voltage/phase combination. Row links open each result page in three-phase mode.

HP	Running Amps (calculated)	NEC Table 430.250 FLC	LRA Estimate (5-7× FLC)
1/8 HP	0.3583 A	off-table	n/a
1/6 HP	0.4778 A	off-table	n/a
1/4 HP	0.7165 A	off-table	n/a
1/3 HP	0.9552 A	off-table	n/a
1/2 HP	1.43 A	2.4 A	12-16.8 A
3/4 HP	2.15 A	3.5 A	17.5-24.5 A
1 HP	2.87 A	4.6 A	23-32.2 A
1.5 HP	4.3 A	6.6 A	33-46.2 A
2 HP	5.73 A	7.5 A	37.5-52.5 A
3 HP	8.6 A	10.6 A	53-74.2 A
5 HP	14.33 A	16.7 A	83.5-116.9 A
7.5 HP	21.5 A	24.2 A	121-169.4 A
10 HP	28.66 A	30.8 A	154-215.6 A
15 HP	42.99 A	46.2 A	231-323.4 A
20 HP	57.32 A	59.4 A	297-415.8 A
25 HP	71.65 A	74.8 A	374-523.6 A
30 HP	85.98 A	88 A	440-616 A
40 HP	114.64 A	114 A	570-798 A
50 HP	143.3 A	143 A	715-1,001 A
75 HP	214.95 A	211 A	1,055-1,477 A

Same HP, Other Voltages (three-phase)

speed 15 HP at 120V = 74.52A per line speed 15 HP at 220V = 40.65A per line speed 15 HP at 230V = 38.88A per line speed 15 HP at 240V = 37.26A per line speed 15 HP at 400V = 22.35A per line speed 15 HP at 480V = 18.63A per line

Related Calculations

bolt 13,165W electrical input to amps at 208V payments 13,165W running cost cable Wire size for 57.75A at 208V (3Φ) (NEC 430.22 minimum: 125% of 46.2A NEC Table 430.250 FLC)

Frequently Asked Questions

How many amps does a 15 HP three-phase motor draw at 208V?expand_more

At the terminals, a 15 HP three-phase motor at 208V draws about 42.99 amps per line at 85% efficiency and 0.85 power factor. For NEC branch-circuit sizing use the NEC Table 430.250 full-load current instead: 46.2 A.

What branch-circuit context does a 15 HP three-phase motor at 208V typically sit in?expand_more

Three-phase motor branches are not served from residential receptacles in the US. Three-phase power is distributed to commercial and industrial services, and a 15 HP three-phase motor at 208V needs a dedicated three-phase branch circuit sized by an electrician per NEC 430.22 (conductors) and 430.52(C)(1) (short-circuit / ground-fault protection), against the motor nameplate and install conditions.

What is locked rotor amps for a 15 HP three-phase motor?expand_more

Locked-rotor (startup) current typically runs 5-7 times the NEC Table 430.250 FLC for a squirrel-cage induction motor: 231-323.4 A for 2-5 seconds. The exact value depends on the NEMA code letter stamped on the motor nameplate.

How much does a 15 HP motor cost to run?expand_more

Operating cost is based on electrical input, not mechanical HP output. At 85% efficiency, a 15 HP motor draws about 13,164.71 W at the terminals. At $0.17/kWh (US residential average, last reviewed April 2026), that is $2.24/hour or $537.12/month at 8 hours/day.

Does motor efficiency affect amp draw?expand_more

Yes. A 15 HP three-phase motor at 90% efficiency draws 40.6 A at the terminals versus 48.72 A at 75% efficiency. Higher efficiency means lower running amps and lower electrical input wattage for the same mechanical output.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.