How Many Amps Is 250 kVA at 400V?

At 400V, a 250 kVA three-phase load draws 360.84 amps per line. kVA is apparent power, so the current is set by kVA and the voltage alone, without a power-factor term. The equivalent single-phase current at this voltage is 625 amps.

250 kVA equals 360.84 amps at 400 volts (three-phase, L-L)

360.84 Amps

Single Phase (400V)625 A

Try: 200kVA at 400V 150kVA at 400V 100kVA at 400V 75kVA at 400V

kVA

Volts

Amps (3Φ per line)

360.84

Assumes an AC three-phase line-to-line circuit at the input voltage. kVA is apparent power, so no power factor term is involved.

Formulas

Single Phase

I_(A) = (kVA × 1000) ÷ V

(250 × 1000) ÷ 400 = 250,000 ÷ 400 = 625 A

Three Phase (400V Line-to-Line)

I_(A) = (kVA × 1000) ÷ (V_L-L × √3)

250,000 ÷ (400 × 1.732) = 250,000 ÷ 692.8 = 360.84 A

Applies to 400/230 systems where 400V is the line-to-line voltage.

Single Phase vs Three Phase

The same 250 kVA unit draws very different current depending on the phase configuration:

Configuration	Formula	Current at 400V
Single Phase	250,000 ÷ 400	625 A
Three Phase (400V L-L)	250,000 ÷ (400 × √3)	360.84 A

For this specific case, 250 kVA at 400V, three-phase carries about 42.26% less current per line than single-phase at the same voltage. That gap tracks the 1 ÷ √3 factor for L-L three-phase (or 1 ÷ 3 for L-N), which is why three-phase distribution is common at commercial and industrial scale: the same apparent power rides on smaller conductors and smaller breakers (applies to 400/230 systems).

Generator & UPS Sizing

Load-Side Real Power by Power Factor

A load with an apparent power of 250 kVA draws different amounts of real power depending on the load's own power factor. The table below is a load-side conversion, not a forecast of what a generator or UPS will output for that load: generators and UPS units publish their own independent kW rating set by the engine or inverter design, and that rating is often lower than kVA × the load's PF.

Load Type	Load PF	Load Real Power (kW)	Current at 400V (three-phase, per line)
Resistive (heaters, lights)	1.0	250 kW	360.84 A per line
Mixed typical	0.85	212.5 kW	360.84 A per line
Motors/HVAC	0.80	200 kW	360.84 A per line
Computers/servers (no PFC)	0.65	162.5 kW	360.84 A per line

Note: current draw stays the same across the rows because kVA sets the current, not the load's power factor. PF only affects how much real work (kW) the load does per amp drawn.

Sizing a load against a source. If you are feeding this load from a UPS, generator, or transformer, check the load against both the source's kVA rating AND the source's kW rating. Those are two independent numbers published by the manufacturer. A 10 kVA / 8 kW generator, for example, can supply up to 10 kVA of apparent power AND up to 8 kW of real power, whichever limit is reached first. Do not use the kW figures above as a substitute for the source's published kW rating.

Circuit Sizing: Starting Points

The numbers below are rough order-of-magnitude starting points under typical assumptions (copper conductors, 75°C terminations, short run, no ambient or bundling derates, non-continuous duty). They are not install specs. Actual breaker and wire selection depends on the equipment nameplate, conductor and termination temperature ratings, cable type, run length and voltage-drop target, ambient and bundling conditions, whether the load is continuous, any NEC 430/440 motor or HVAC provisions, and local code.

	Single Phase	Three Phase
Current draw (at full kVA)	625 A	360.84 A

For a real install, run the full wire-size calculator with your actual run length, voltage, and drop target, and verify breaker selection against the equipment nameplate and local code.

Energy Cost at Full Load

A load with an apparent power of 250 kVA at load PF 0.85 draws 212.5 kW of real power. Running cost at that draw: $36.13/hour at $0.17/kWh (rates last reviewed April 2026), or $8,670.00/month (8h/day). Full breakdown.

kW Equivalent

250 kVA at PF 0.85 = 212.5 kW. See 212.5 kW to amps at 400V.

Other kVA Ratings at 400V

kVA	Three Phase Amps (L-L, per line)	Single Phase Amps	Real Power (PF 0.8)
10 kVA	14.43 A	25 A	8 kW
15 kVA	21.65 A	37.5 A	12 kW
20 kVA	28.87 A	50 A	16 kW
25 kVA	36.08 A	62.5 A	20 kW
30 kVA	43.3 A	75 A	24 kW
40 kVA	57.74 A	100 A	32 kW
50 kVA	72.17 A	125 A	40 kW
75 kVA	108.25 A	187.5 A	60 kW
100 kVA	144.34 A	250 A	80 kW
150 kVA	216.51 A	375 A	120 kW
200 kVA	288.68 A	500 A	160 kW
250 kVA	360.84 A	625 A	200 kW

Frequently Asked Questions

How many amps is 250 kVA at 400V?expand_more

250 kVA at 400V is 360.84 amps per line on a three-phase circuit (400/230), or 625 amps on single-phase at the same voltage.

How much fuel does a 250 kVA generator use?expand_more

Fuel burn is set by the generator's specific-fuel-consumption curve, not a rule of thumb tied to the kVA rating. It varies sharply with fuel type (gasoline vs diesel vs natural gas vs propane), load percentage (partial-load efficiency is much worse than full-load), engine size and age, altitude, and ambient temperature. For a specific unit, check the manufacturer's fuel-consumption curve at your expected load percentage. Generic per-hour estimates from the kVA rating alone are not reliable enough to plan fuel capacity from.

What size generator do I need for my loads?expand_more

Generator sizing is not a single-formula calculation. A rough napkin pass is: add up the steady-state watts of everything you plan to run, divide by a planning power factor (often 0.8 but not universal), and add margin. Then cross-check the result against the generator's published kW rating, which is a separate manufacturer spec set by the engine (prime mover) and is not derived from the generator's kVA rating by any formula. The caveats that matter for a real install: motor and compressor inrush can be several times steady-state current, load diversity and sequencing affect peak demand, voltage-dip tolerance of sensitive equipment limits how much motor load a given genset can start, and altitude and ambient temperature both derate output. A load with an apparent power of 250 kVA at PF 0.8 has a real-power draw of 200 kW, but that number alone is not sufficient to size a generator for a real installation.

Three-phase vs single-phase for 250 kVA?expand_more

Three-phase (400/230) draws 360.84A per line. Single-phase at the same voltage draws 625A. Three-phase delivers the same apparent power across three conductors, so each line carries less current and the wire and breakers can be smaller for the same kVA.

What size breaker would I need for 250 kVA at 400V?expand_more

This is a sizing question, not a conversion question, and there is no single answer from a page like this. Breaker selection depends on the equipment nameplate FLA, whether the load is continuous (NEC 210.19(A) applies the 125% continuous-load rule), conductor ampacity and termination temperature, any NEC 430/440 motor or HVAC provisions, and local code. The current draw on this page is the input to that sizing process, not the output. Verify against the equipment nameplate and a licensed electrician.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.