How Many Amps Is 0.8 kW at 575V?

At 575V, 0.8 kW pulls approximately 0.945 amps on AC three-phase (PF 0.85). This is the case typical for commercial HVAC, industrial motors, rooftop units, and three-phase panel loads. Always verify against the equipment nameplate for actual install sizing.

0.8 kW at 575V, AC three-phase (PF 0.85)

0.945 Amps

0.8 kilowatts at 575V on AC three-phase ≈ 0.945 amps

AC Single Phase (PF 0.85)1.64 A

DC (ideal baseline)1.39 A

Try: 0.75kW at 575V 1kW at 575V 0.5kW at 575V 1.5kW at 575V

Volts

Amps (AC three-phase, PF 0.85)

0.945

Formulas

DC: kW to Amps

I_(A) = 1000 × P_(kW) ÷ V_(V)

1000 × 0.8 ÷ 575 = 800 ÷ 575 = 1.39 A

AC Single Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (PF × V_(V))

800 ÷ (0.85 × 575) = 800 ÷ 488.75 = 1.64 A

AC Three Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (√3 × PF × V_L-L), where V_L-L is the line-to-line voltage

800 ÷ (1.732 × 0.85 × 575) = 800 ÷ 846.52 = 0.945 A

Equipment & Circuit Sizing

Breaker Sizing

Breaker ratings are in amps, not watts, so the real install answer depends on the equipment nameplate FLA, whether the load is continuous (NEC 210.19(A) sizes the conductor and OCP at 125% of a continuous load, equivalently 80% of breaker rating), conductor ampacity and temperature rating, ambient and bundling derates, and any motor or HVAC provisions (NEC 430 / 440). At roughly 0.945A on AC three-phase at 575V, the load sits in the bracket between a 15A standard size (non-continuous) and the next size up that covers a continuous load under 210.19(A). The actual install pick depends on whether the load is continuous and the factors above; a conversion page can't pick a single "right" breaker from the amp draw alone.

Energy Cost

0.8 kW costs $0.14/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC three-phase)

How the line current for 0.8 kW at 575V changes with load power factor, on the same AC three-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load Type	PF	0.8 kW at 575V (AC three-phase)
Resistive (heaters, incandescent)	1	0.8033 A
Fluorescent lamps	0.95	0.8455 A
LED lighting	0.9	0.8925 A
Synchronous motors	0.9	0.8925 A
Typical mixed loads	0.85	0.945 A
Induction motors (full load)	0.8	1 A
Computers (without PFC)	0.65	1.24 A
Induction motors (no load)	0.35	2.3 A

AC Conversion Comparison

On DC, 0.8kW at 575V draws 1.39A. AC single-phase at PF 0.85 pulls 1.64A because reactive current is added on top of the real power. Three-phase at the same voltage needs only 0.945A per line since the same 0.8kW is shared across three conductors instead of one.

Circuit Type	Formula	Result
DC	800 ÷ 575	1.39 A
AC Single Phase (PF 0.85)	800 ÷ (0.85 × 575)	1.64 A
AC Three Phase (PF 0.85)	800 ÷ (1.732 × 0.85 × 575)	0.945 A

Other kW Values at 575V

kW	AC 3-Phase per line, PF 0.85	AC 1-Phase PF 0.85
0.5 kW	0.5906 A	1.02 A
0.75 kW	0.886 A	1.53 A
1 kW	1.18 A	2.05 A
1.5 kW	1.77 A	3.07 A
2 kW	2.36 A	4.09 A
2.5 kW	2.95 A	5.12 A
3 kW	3.54 A	6.14 A
3.5 kW	4.13 A	7.16 A
4 kW	4.73 A	8.18 A
5 kW	5.91 A	10.23 A
6 kW	7.09 A	12.28 A
7.5 kW	8.86 A	15.35 A
8 kW	9.45 A	16.37 A
10 kW	11.81 A	20.46 A
12 kW	14.18 A	24.55 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

Related Calculations

bolt 800W to amps at 575V payments 800W running cost cable Wire size for 0.945A at 575V (3Φ)

Frequently Asked Questions

How many amps is 0.8 kW at 575V?expand_more

0.8 kW at 575V draws about 0.945 amps on an AC three-phase circuit at PF 0.85. Alternate cases at the same voltage: 1.39A on DC, 1.64A on AC single-phase.

How much does 0.8 kW cost to run?expand_more

0.8 kW costs $0.14 per hour at $0.17/kWh (US residential average, last reviewed April 2026). At 8 hours/day that is $32.64 per month.

How does three-phase affect the amps for 0.8 kW?expand_more

Three-phase at 575V draws 0.945A per line versus 1.64A single-phase. Less current per conductor means smaller wire and lower I²R losses.

What size breaker would I need for 0.8 kW at 575V?expand_more

This is a sizing question, not a conversion question, and there is no single correct answer from a page like this. Breaker selection depends on the equipment nameplate FLA, whether the load is continuous (NEC 210.19(A) applies the 125% continuous-load rule), the conductor ampacity and temperature rating, any NEC 430/440 motor or HVAC provisions, and local code interpretation. Use the nameplate and a licensed electrician for the real install value; use this page only for the current-draw estimate that feeds into that process.

Why do industrial systems use kW instead of watts?expand_more

Industrial equipment operates at higher power levels. 0.8 kW is easier to express than 800W. The math is identical, just scaled by 1000.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.