How Many Amps Is 13.08 kW at 240V?

At 240V, 13.08 kW pulls approximately 64.12 amps on AC single-phase (PF 0.85). This is the case typical for residential water heaters, dryers, ranges, EV chargers, and HVAC equipment. Always verify against the equipment nameplate for actual install sizing.

13.08 kW at 240V, AC single-phase (PF 0.85)

64.12 Amps

13.08 kilowatts at 240V on AC single-phase ≈ 64.12 amps

DC (ideal baseline)54.5 A

Try: 12kW at 240V 15kW at 240V 10kW at 240V 18kW at 240V

Volts

Amps (AC single-phase, PF 0.85)

64.12

Formulas

DC: kW to Amps

I_(A) = 1000 × P_(kW) ÷ V_(V)

1000 × 13.08 ÷ 240 = 13,080 ÷ 240 = 54.5 A

AC Single Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (PF × V_(V))

13,080 ÷ (0.85 × 240) = 13,080 ÷ 204 = 64.12 A

Equipment & Circuit Sizing

Breaker Sizing

Breaker ratings are in amps, not watts, so the real install answer depends on the equipment nameplate FLA, whether the load is continuous (NEC 210.19(A) sizes the conductor and OCP at 125% of a continuous load, equivalently 80% of breaker rating), conductor ampacity and temperature rating, ambient and bundling derates, and any motor or HVAC provisions (NEC 430 / 440). At roughly 64.12A on AC single-phase at 240V, the load sits in the bracket between a 70A standard size (non-continuous) and the next size up that covers a continuous load under 210.19(A) (around 90A). The actual install pick depends on whether the load is continuous and the factors above; a conversion page can't pick a single "right" breaker from the amp draw alone.

Energy Cost

13.08 kW costs $2.22/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC single-phase)

How the line current for 13.08 kW at 240V changes with load power factor, on the same AC single-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load Type	PF	13.08 kW at 240V (AC single-phase)
Resistive (heaters, incandescent)	1	54.5 A
Fluorescent lamps	0.95	57.37 A
LED lighting	0.9	60.56 A
Synchronous motors	0.9	60.56 A
Typical mixed loads	0.85	64.12 A
Induction motors (full load)	0.8	68.13 A
Computers (without PFC)	0.65	83.85 A
Induction motors (no load)	0.35	155.71 A

AC Conversion Comparison

On DC, 13.08kW at 240V draws 54.5A. AC single-phase at PF 0.85 pulls 64.12A because reactive current is added on top of the real power.

Circuit Type	Formula	Result
DC	13,080 ÷ 240	54.5 A
AC Single Phase (PF 0.85)	13,080 ÷ (0.85 × 240)	64.12 A

Other kW Values at 240V

kW	AC 1-Phase PF 0.85	DC Amps PF 1.0 baseline
2 kW	9.8 A	8.33 A
2.5 kW	12.25 A	10.42 A
3 kW	14.71 A	12.5 A
3.5 kW	17.16 A	14.58 A
4 kW	19.61 A	16.67 A
5 kW	24.51 A	20.83 A
6 kW	29.41 A	25 A
7.5 kW	36.76 A	31.25 A
8 kW	39.22 A	33.33 A
10 kW	49.02 A	41.67 A
12 kW	58.82 A	50 A
15 kW	73.53 A	62.5 A
18 kW	88.24 A	75 A
20 kW	98.04 A	83.33 A
22 kW	107.84 A	91.67 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

Related Calculations

bolt 13,080W to amps at 240V payments 13,080W running cost cable Wire size for 64.12A at 240V

Frequently Asked Questions

How many amps is 13.08 kW at 240V?expand_more

13.08 kW at 240V draws about 64.12 amps on an AC single-phase circuit at PF 0.85. Alternate cases at the same voltage: 54.5A on DC.

Is 13.08 kW single-phase or three-phase?expand_more

13.08 kW is available in both, but three-phase is more common for commercial HVAC, rooftop units, and motors once you reach this range.

Why do industrial systems use kW instead of watts?expand_more

Industrial equipment operates at higher power levels. 13.08 kW is easier to express than 13,080W. The math is identical, just scaled by 1000.

What size breaker would I need for 13.08 kW at 240V?expand_more

This is a sizing question, not a conversion question, and there is no single correct answer from a page like this. Breaker selection depends on the equipment nameplate FLA, whether the load is continuous (NEC 210.19(A) applies the 125% continuous-load rule), the conductor ampacity and temperature rating, any NEC 430/440 motor or HVAC provisions, and local code interpretation. Use the nameplate and a licensed electrician for the real install value; use this page only for the current-draw estimate that feeds into that process.

How many amps does a 13.08 kW EV charger draw at 240V?expand_more

At 240V, a 13.08 kW EVSE draws about 64.12A on AC single-phase at PF 0.85. This is Level 2 territory, the standard residential (240V) or commercial (208V) AC charging tier covered by NEC Article 625. Home Level 2 units are typically 7.2 to 19.2 kW (30-80A); anything above that is usually commercial hardware or DC fast charging.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.