How Many Amps Is 18.42 kW at 24V?

At 24V, 18.42 kW pulls approximately 767.54 amps on DC (PF 0.85). This is the case typical for solar arrays, battery banks, and DC industrial equipment. Always verify against the equipment nameplate for actual install sizing.

18.42 kW at 24V, DC (PF 0.85)
767.54 Amps
18.42 kilowatts at 24V on DC ≈ 767.54 amps
AC Single Phase (PF 0.85)902.99 A
767.54

Formulas

DC: kW to Amps

I(A) = 1000 × P(kW) ÷ V(V)

1000 × 18.42 ÷ 24 = 18,421 ÷ 24 = 767.54 A

AC Single Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (PF × V(V))

18,421 ÷ (0.85 × 24) = 18,421 ÷ 20.4 = 902.99 A

Equipment & Circuit Sizing

Energy Cost

18.42 kW costs $3.13/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (DC)

How the line current for 18.42 kW at 24V changes with load power factor, on the same DC circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load TypePF18.42 kW at 24V (DC)
Resistive (heaters, incandescent)1767.54 A
Fluorescent lamps0.95767.54 A
LED lighting0.9767.54 A
Synchronous motors0.9767.54 A
Typical mixed loads0.85767.54 A
Induction motors (full load)0.8767.54 A
Computers (without PFC)0.65767.54 A
Induction motors (no load)0.35767.54 A

AC Conversion Comparison

On DC, 18.42kW at 24V draws 767.54A. AC single-phase at PF 0.85 pulls 902.99A because reactive current is added on top of the real power.

Circuit TypeFormulaResult
DC18,421 ÷ 24767.54 A
AC Single Phase (PF 0.85)18,421 ÷ (0.85 × 24)902.99 A

Other kW Values at 24V

kWDC AmpsAC 1-Phase PF 0.85
3 kW125 A147.06 A
3.5 kW145.83 A171.57 A
4 kW166.67 A196.08 A
5 kW208.33 A245.1 A
6 kW250 A294.12 A
7.5 kW312.5 A367.65 A
8 kW333.33 A392.16 A
10 kW416.67 A490.2 A
12 kW500 A588.24 A
15 kW625 A735.29 A
18 kW750 A882.35 A
20 kW833.33 A980.39 A
22 kW916.67 A1,078.43 A
25 kW1,041.67 A1,225.49 A
30 kW1,250 A1,470.59 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

Frequently Asked Questions

18.42 kW at 24V draws about 767.54 amps on DC. Alternate cases at the same voltage: 902.99A on AC single-phase.
On AC single-phase, current scales inversely with power factor. At PF 1.0 (pure resistive, like a heater), 18.42 kW at 24V draws 767.54A. At PF 0.80 (typical induction motor), the same real power draws 959.43A. The extra current is reactive and does no real work, but still flows through the wire and the breaker.
18.42 kW equals 18,421 watts. Multiply kilowatts by 1000.
At 24V, this is Level 1 territory (120V AC, single-phase, typically 12-16A). A 18.42 kW draw on a standard 120V household outlet is at or above the 1,440W NEC 210.19(A) continuous figure, which is why Level 1 EVSE ships at 1.4-1.9 kW and takes 20+ hours for a full charge. If you need 18.42 kW of charging, you want Level 2 on a 240V dedicated circuit, not 120V.
Industrial equipment operates at higher power levels. 18.42 kW is easier to express than 18,421W. The math is identical, just scaled by 1000.
This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.