How Many Amps Is 3.32 kW at 240V?

3.32 kW at 240V draws about 16.29 amps on an AC single-phase circuit at PF 0.85, typical for residential water heaters, dryers, ranges, EV chargers, and HVAC equipment. Actual current varies with equipment power factor and duty cycle.

3.32 kW at 240V, AC single-phase (PF 0.85)

16.29 Amps

3.32 kilowatts at 240V on AC single-phase ≈ 16.29 amps

DC (ideal baseline)13.85 A

Try: 3.5kW at 240V 3kW at 240V 4kW at 240V 2.5kW at 240V

Volts

Amps (AC single-phase, PF 0.85)

16.29

Formulas

DC: kW to Amps

I_(A) = 1000 × P_(kW) ÷ V_(V)

1000 × 3.32 ÷ 240 = 3,324 ÷ 240 = 13.85 A

AC Single Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (PF × V_(V))

3,324 ÷ (0.85 × 240) = 3,324 ÷ 204 = 16.29 A

Equipment & Circuit Sizing

Breaker Sizing

Breaker ratings are in amps, not watts, so the real install answer depends on the equipment nameplate FLA, whether the load is continuous (NEC 210.19(A) sizes the conductor and OCP at 125% of a continuous load, equivalently 80% of breaker rating), conductor ampacity and temperature rating, ambient and bundling derates, and any motor or HVAC provisions (NEC 430 / 440). At roughly 16.29A on AC single-phase at 240V, the load sits in the bracket between a 20A standard size (non-continuous) and the next size up that covers a continuous load under 210.19(A) (around 25A). The actual install pick depends on whether the load is continuous and the factors above; a conversion page can't pick a single "right" breaker from the amp draw alone.

Energy Cost

3.32 kW costs $0.57/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC single-phase)

How the line current for 3.32 kW at 240V changes with load power factor, on the same AC single-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load Type	PF	3.32 kW at 240V (AC single-phase)
Resistive (heaters, incandescent)	1	13.85 A
Fluorescent lamps	0.95	14.58 A
LED lighting	0.9	15.39 A
Synchronous motors	0.9	15.39 A
Typical mixed loads	0.85	16.29 A
Induction motors (full load)	0.8	17.31 A
Computers (without PFC)	0.65	21.31 A
Induction motors (no load)	0.35	39.57 A

AC Conversion Comparison

On DC, 3.32kW at 240V draws 13.85A. AC single-phase at PF 0.85 pulls 16.29A because reactive current is added on top of the real power.

Circuit Type	Formula	Result
DC	3,324 ÷ 240	13.85 A
AC Single Phase (PF 0.85)	3,324 ÷ (0.85 × 240)	16.29 A

Other kW Values at 240V

kW	AC 1-Phase PF 0.85	DC Amps PF 1.0 baseline
0.5 kW	2.45 A	2.08 A
0.75 kW	3.68 A	3.13 A
1 kW	4.9 A	4.17 A
1.5 kW	7.35 A	6.25 A
2 kW	9.8 A	8.33 A
2.5 kW	12.25 A	10.42 A
3 kW	14.71 A	12.5 A
3.5 kW	17.16 A	14.58 A
4 kW	19.61 A	16.67 A
5 kW	24.51 A	20.83 A
6 kW	29.41 A	25 A
7.5 kW	36.76 A	31.25 A
8 kW	39.22 A	33.33 A
10 kW	49.02 A	41.67 A
12 kW	58.82 A	50 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

Related Calculations

bolt 3,324W to amps at 240V payments 3,324W running cost cable Wire size for 16.29A at 240V

Frequently Asked Questions

How many amps is 3.32 kW at 240V?expand_more

3.32 kW at 240V draws about 16.29 amps on an AC single-phase circuit at PF 0.85. Alternate cases at the same voltage: 13.85A on DC.

Is 3.32 kW single-phase or three-phase?expand_more

3.32 kW can be either. Residential loads up to about 5 kW (water heaters, dryers, EV chargers at 240V) are usually single-phase; commercial panels often serve the same load three-phase at 208V or 480V.

How much does 3.32 kW cost to run?expand_more

3.32 kW costs $0.57 per hour at $0.17/kWh (US residential average, last reviewed April 2026). At 8 hours/day that is $135.62 per month.

What is the formula for kW to amps?expand_more

DC: Amps = (kW × 1000) ÷ Volts. AC single-phase: Amps = (kW × 1000) ÷ (Volts × PF). AC three-phase: Amps = (kW × 1000) ÷ (Volts_L-L × √3 × PF).

How many amps does a 3.32 kW EV charger draw at 240V?expand_more

At 240V, a 3.32 kW EVSE draws about 16.29A on AC single-phase at PF 0.85. This is Level 2 territory, the standard residential (240V) or commercial (208V) AC charging tier covered by NEC Article 625. Home Level 2 units are typically 7.2 to 19.2 kW (30-80A); anything above that is usually commercial hardware or DC fast charging.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.