How Many Amps Is 326 kW at 575V?

At 575V, 326 kW pulls approximately 385.1 amps on AC three-phase (PF 0.85). This is the case typical for commercial HVAC, industrial motors, rooftop units, and three-phase panel loads. Always verify against the equipment nameplate for actual install sizing.

326 kW at 575V, AC three-phase (PF 0.85)

385.1 Amps

326 kilowatts at 575V on AC three-phase ≈ 385.1 amps

AC Single Phase (PF 0.85)667.01 A

DC (ideal baseline)566.96 A

Try: 200kW at 575V 150kW at 575V 125kW at 575V 100kW at 575V

Volts

Amps (AC three-phase, PF 0.85)

385.1

Formulas

DC: kW to Amps

I_(A) = 1000 × P_(kW) ÷ V_(V)

1000 × 326 ÷ 575 = 326,000 ÷ 575 = 566.96 A

AC Single Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (PF × V_(V))

326,000 ÷ (0.85 × 575) = 326,000 ÷ 488.75 = 667.01 A

AC Three Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (√3 × PF × V_L-L), where V_L-L is the line-to-line voltage

326,000 ÷ (1.732 × 0.85 × 575) = 326,000 ÷ 846.52 = 385.1 A

Equipment & Circuit Sizing

Breaker Sizing

Breaker ratings are in amps, not watts, so the real install answer depends on the equipment nameplate FLA, whether the load is continuous (NEC 210.19(A) sizes the conductor and OCP at 125% of a continuous load, equivalently 80% of breaker rating), conductor ampacity and temperature rating, ambient and bundling derates, and any motor or HVAC provisions (NEC 430 / 440). At roughly 385.1A on AC three-phase at 575V, the load sits in the bracket between a 400A standard size (non-continuous) and the next size up that covers a continuous load under 210.19(A) (around 500A). The actual install pick depends on whether the load is continuous and the factors above; a conversion page can't pick a single "right" breaker from the amp draw alone.

Energy Cost

326 kW costs $55.42/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC three-phase)

How the line current for 326 kW at 575V changes with load power factor, on the same AC three-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load Type	PF	326 kW at 575V (AC three-phase)
Resistive (heaters, incandescent)	1	327.33 A
Fluorescent lamps	0.95	344.56 A
LED lighting	0.9	363.7 A
Synchronous motors	0.9	363.7 A
Typical mixed loads	0.85	385.1 A
Induction motors (full load)	0.8	409.17 A
Computers (without PFC)	0.65	503.59 A
Induction motors (no load)	0.35	935.24 A

AC Conversion Comparison

On DC, 326kW at 575V draws 566.96A. AC single-phase at PF 0.85 pulls 667.01A because reactive current is added on top of the real power. Three-phase at the same voltage needs only 385.1A per line since the same 326kW is shared across three conductors instead of one.

Circuit Type	Formula	Result
DC	326,000 ÷ 575	566.96 A
AC Single Phase (PF 0.85)	326,000 ÷ (0.85 × 575)	667.01 A
AC Three Phase (PF 0.85)	326,000 ÷ (1.732 × 0.85 × 575)	385.1 A

Other kW Values at 575V

kW	AC 3-Phase per line, PF 0.85	AC 1-Phase PF 0.85
15 kW	17.72 A	30.69 A
18 kW	21.26 A	36.83 A
20 kW	23.63 A	40.92 A
22 kW	25.99 A	45.01 A
25 kW	29.53 A	51.15 A
30 kW	35.44 A	61.38 A
35 kW	41.34 A	71.61 A
40 kW	47.25 A	81.84 A
50 kW	59.06 A	102.3 A
60 kW	70.88 A	122.76 A
75 kW	88.6 A	153.45 A
100 kW	118.13 A	204.6 A
125 kW	147.66 A	255.75 A
150 kW	177.19 A	306.91 A
200 kW	236.26 A	409.21 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

electrical_services 326 kW at 208V = 1,064.57A (3-phase) electrical_services 326 kW at 400V = 553.58A (3-phase) electrical_services 326 kW at 460V = 481.37A (3-phase) electrical_services 326 kW at 480V = 461.31A (3-phase)

Related Calculations

bolt 326,000W to amps at 575V payments 326,000W running cost cable Wire size for 385.1A at 575V (3Φ)

Frequently Asked Questions

How many amps is 326 kW at 575V?expand_more

326 kW at 575V draws about 385.1 amps on an AC three-phase circuit at PF 0.85. Alternate cases at the same voltage: 566.96A on DC, 667.01A on AC single-phase.

Why do industrial systems use kW instead of watts?expand_more

Industrial equipment operates at higher power levels. 326 kW is easier to express than 326,000W. The math is identical, just scaled by 1000.

What size breaker would I need for 326 kW at 575V?expand_more

This is a sizing question, not a conversion question, and there is no single correct answer from a page like this. Breaker selection depends on the equipment nameplate FLA, whether the load is continuous (NEC 210.19(A) applies the 125% continuous-load rule), the conductor ampacity and temperature rating, any NEC 430/440 motor or HVAC provisions, and local code interpretation. Use the nameplate and a licensed electrician for the real install value; use this page only for the current-draw estimate that feeds into that process.

How does three-phase affect the amps for 326 kW?expand_more

Three-phase at 575V draws 385.1A per line versus 667.01A single-phase. Less current per conductor means smaller wire and lower I²R losses.

What is the formula for kW to amps?expand_more

DC: Amps = (kW × 1000) ÷ Volts. AC single-phase: Amps = (kW × 1000) ÷ (Volts × PF). AC three-phase: Amps = (kW × 1000) ÷ (Volts_L-L × √3 × PF).

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.