How Many Amps Is 33.6 kW at 575V?
33.6 kilowatts at 575V works out to roughly 39.69 amps on AC three-phase at PF 0.85. That is typical for commercial HVAC, industrial motors, rooftop units, and three-phase panel loads. See the DC and alternate-phase numbers below for other circuit types.
Use this citation when referencing this page.
Formulas
DC: kW to Amps
I(A) = 1000 × P(kW) ÷ V(V)
AC Single Phase (PF = 0.85)
I(A) = 1000 × P(kW) ÷ (PF × V(V))
AC Three Phase (PF = 0.85)
I(A) = 1000 × P(kW) ÷ (√3 × PF × VL-L), where VL-L is the line-to-line voltage
Equipment & Circuit Sizing
Breaker Sizing
Breaker ratings are in amps, not watts, so the real install answer depends on the equipment nameplate FLA, whether the load is continuous (NEC 210.19(A) sizes the conductor and OCP at 125% of a continuous load, equivalently 80% of breaker rating), conductor ampacity and temperature rating, ambient and bundling derates, and any motor or HVAC provisions (NEC 430 / 440). At roughly 39.69A on AC three-phase at 575V, the load sits in the bracket between a 40A standard size (non-continuous) and the next size up that covers a continuous load under 210.19(A) (around 50A). The actual install pick depends on whether the load is continuous and the factors above; a conversion page can't pick a single "right" breaker from the amp draw alone.
Energy Cost
33.6 kW costs $5.71/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.
Power Factor Reference (AC three-phase)
How the line current for 33.6 kW at 575V changes with load power factor, on the same AC three-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.
| Load Type | PF | 33.6 kW at 575V (AC three-phase) |
|---|---|---|
| Resistive (heaters, incandescent) | 1 | 33.74 A |
| Fluorescent lamps | 0.95 | 35.51 A |
| LED lighting | 0.9 | 37.49 A |
| Synchronous motors | 0.9 | 37.49 A |
| Typical mixed loads | 0.85 | 39.69 A |
| Induction motors (full load) | 0.8 | 42.17 A |
| Computers (without PFC) | 0.65 | 51.9 A |
| Induction motors (no load) | 0.35 | 96.39 A |
AC Conversion Comparison
On DC, 33.6kW at 575V draws 58.43A. AC single-phase at PF 0.85 pulls 68.75A because reactive current is added on top of the real power. Three-phase at the same voltage needs only 39.69A per line since the same 33.6kW is shared across three conductors instead of one.
| Circuit Type | Formula | Result |
|---|---|---|
| DC | 33,600 ÷ 575 | 58.43 A |
| AC Single Phase (PF 0.85) | 33,600 ÷ (0.85 × 575) | 68.75 A |
| AC Three Phase (PF 0.85) | 33,600 ÷ (1.732 × 0.85 × 575) | 39.69 A |
Other kW Values at 575V
| kW | AC 3-Phase per line, PF 0.85 | AC 1-Phase PF 0.85 |
|---|---|---|
| 6 kW | 7.09 A | 12.28 A |
| 7.5 kW | 8.86 A | 15.35 A |
| 8 kW | 9.45 A | 16.37 A |
| 10 kW | 11.81 A | 20.46 A |
| 12 kW | 14.18 A | 24.55 A |
| 15 kW | 17.72 A | 30.69 A |
| 18 kW | 21.26 A | 36.83 A |
| 20 kW | 23.63 A | 40.92 A |
| 22 kW | 25.99 A | 45.01 A |
| 25 kW | 29.53 A | 51.15 A |
| 30 kW | 35.44 A | 61.38 A |
| 35 kW | 41.34 A | 71.61 A |
| 40 kW | 47.25 A | 81.84 A |
| 50 kW | 59.06 A | 102.3 A |
| 60 kW | 70.88 A | 122.76 A |
Same kW, Other Voltages
Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.