How Many Amps Is 338.62 kW at 460V?

338.62 kW at 460V draws about 500 amps on an AC three-phase circuit at PF 0.85, typical for commercial HVAC, industrial motors, rooftop units, and three-phase panel loads. Actual current varies with equipment power factor and duty cycle.

338.62 kW at 460V, AC three-phase (PF 0.85)

500 Amps

338.62 kilowatts at 460V on AC three-phase ≈ 500 amps

AC Single Phase (PF 0.85)866.03 A

DC (ideal baseline)736.12 A

Try: 200kW at 460V 150kW at 460V 125kW at 460V 100kW at 460V

Volts

Amps (AC three-phase, PF 0.85)

500

Formulas

DC: kW to Amps

I_(A) = 1000 × P_(kW) ÷ V_(V)

1000 × 338.62 ÷ 460 = 338,616 ÷ 460 = 736.12 A

AC Single Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (PF × V_(V))

338,616 ÷ (0.85 × 460) = 338,616 ÷ 391 = 866.03 A

AC Three Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (√3 × PF × V_L-L), where V_L-L is the line-to-line voltage

338,616 ÷ (1.732 × 0.85 × 460) = 338,616 ÷ 677.21 = 500 A

Equipment & Circuit Sizing

Breaker Sizing

Breaker ratings are in amps, not watts, so the real install answer depends on the equipment nameplate FLA, whether the load is continuous (NEC 210.19(A) sizes the conductor and OCP at 125% of a continuous load, equivalently 80% of breaker rating), conductor ampacity and temperature rating, ambient and bundling derates, and any motor or HVAC provisions (NEC 430 / 440). At roughly 500A on AC three-phase at 460V, the load sits in the bracket between a 600A standard size (non-continuous) and the next size up that covers a continuous load under 210.19(A). The actual install pick depends on whether the load is continuous and the factors above; a conversion page can't pick a single "right" breaker from the amp draw alone.

Energy Cost

338.62 kW costs $57.56/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC three-phase)

How the line current for 338.62 kW at 460V changes with load power factor, on the same AC three-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load Type	PF	338.62 kW at 460V (AC three-phase)
Resistive (heaters, incandescent)	1	425 A
Fluorescent lamps	0.95	447.37 A
LED lighting	0.9	472.22 A
Synchronous motors	0.9	472.22 A
Typical mixed loads	0.85	500 A
Induction motors (full load)	0.8	531.25 A
Computers (without PFC)	0.65	653.85 A
Induction motors (no load)	0.35	1,214.29 A

AC Conversion Comparison

On DC, 338.62kW at 460V draws 736.12A. AC single-phase at PF 0.85 pulls 866.03A because reactive current is added on top of the real power. Three-phase at the same voltage needs only 500A per line since the same 338.62kW is shared across three conductors instead of one.

Circuit Type	Formula	Result
DC	338,616 ÷ 460	736.12 A
AC Single Phase (PF 0.85)	338,616 ÷ (0.85 × 460)	866.03 A
AC Three Phase (PF 0.85)	338,616 ÷ (1.732 × 0.85 × 460)	500 A

Other kW Values at 460V

kW	AC 3-Phase per line, PF 0.85	AC 1-Phase PF 0.85
15 kW	22.15 A	38.36 A
18 kW	26.58 A	46.04 A
20 kW	29.53 A	51.15 A
22 kW	32.49 A	56.27 A
25 kW	36.91 A	63.94 A
30 kW	44.3 A	76.73 A
35 kW	51.68 A	89.51 A
40 kW	59.06 A	102.3 A
50 kW	73.83 A	127.88 A
60 kW	88.6 A	153.45 A
75 kW	110.74 A	191.82 A
100 kW	147.66 A	255.75 A
125 kW	184.57 A	319.69 A
150 kW	221.49 A	383.63 A
200 kW	295.32 A	511.51 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

electrical_services 338.62 kW at 208V = 1,105.77A (3-phase) electrical_services 338.62 kW at 400V = 575A (3-phase) electrical_services 338.62 kW at 480V = 479.17A (3-phase) electrical_services 338.62 kW at 575V = 400A (3-phase)

Related Calculations

bolt 338,616W to amps at 460V payments 338,616W running cost cable Wire size for 500A at 460V (3Φ)

Frequently Asked Questions

How many amps is 338.62 kW at 460V?expand_more

338.62 kW at 460V draws about 500 amps on an AC three-phase circuit at PF 0.85. Alternate cases at the same voltage: 736.12A on DC, 866.03A on AC single-phase.

What is the formula for kW to amps?expand_more

DC: Amps = (kW × 1000) ÷ Volts. AC single-phase: Amps = (kW × 1000) ÷ (Volts × PF). AC three-phase: Amps = (kW × 1000) ÷ (Volts_L-L × √3 × PF).

How many amps does a 338.62 kW EV charger draw at 460V?expand_more

460V is commercial/industrial panel voltage, not a typical AC EVSE feed to a vehicle. On three-phase 460V, 338.62 kW works out to about 500A per line (three-phase at PF 0.85). In practice, 400-480V three-phase is usually the AC input to a DC fast charger (50-350 kW CCS/NACS stations like Tesla Superchargers), which rectifies to DC and delivers that directly to the vehicle, rather than an AC EVSE connector. A 338.62 kW figure at 460V is most likely the AC feed to a smaller commercial cabinet or the control-side input of a larger DC fast charger, not an at-the-car AC current.

How does three-phase affect the amps for 338.62 kW?expand_more

Three-phase at 460V draws 500A per line versus 866.03A single-phase. Less current per conductor means smaller wire and lower I²R losses.

What size breaker would I need for 338.62 kW at 460V?expand_more

This is a sizing question, not a conversion question, and there is no single correct answer from a page like this. Breaker selection depends on the equipment nameplate FLA, whether the load is continuous (NEC 210.19(A) applies the 125% continuous-load rule), the conductor ampacity and temperature rating, any NEC 430/440 motor or HVAC provisions, and local code interpretation. Use the nameplate and a licensed electrician for the real install value; use this page only for the current-draw estimate that feeds into that process.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.