How Many Amps Is 42.33 kW at 460V?

At 460V, 42.33 kW pulls approximately 62.5 amps on AC three-phase (PF 0.85). This is the case typical for commercial HVAC, industrial motors, rooftop units, and three-phase panel loads. Always verify against the equipment nameplate for actual install sizing.

42.33 kW at 460V, AC three-phase (PF 0.85)

62.5 Amps

42.33 kilowatts at 460V on AC three-phase ≈ 62.5 amps

AC Single Phase (PF 0.85)108.25 A

DC (ideal baseline)92.02 A

Try: 40kW at 460V 35kW at 460V 50kW at 460V 30kW at 460V

Volts

Amps (AC three-phase, PF 0.85)

62.5

Formulas

DC: kW to Amps

I_(A) = 1000 × P_(kW) ÷ V_(V)

1000 × 42.33 ÷ 460 = 42,327 ÷ 460 = 92.02 A

AC Single Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (PF × V_(V))

42,327 ÷ (0.85 × 460) = 42,327 ÷ 391 = 108.25 A

AC Three Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (√3 × PF × V_L-L), where V_L-L is the line-to-line voltage

42,327 ÷ (1.732 × 0.85 × 460) = 42,327 ÷ 677.21 = 62.5 A

Equipment & Circuit Sizing

Breaker Sizing

Breaker ratings are in amps, not watts, so the real install answer depends on the equipment nameplate FLA, whether the load is continuous (NEC 210.19(A) sizes the conductor and OCP at 125% of a continuous load, equivalently 80% of breaker rating), conductor ampacity and temperature rating, ambient and bundling derates, and any motor or HVAC provisions (NEC 430 / 440). At roughly 62.5A on AC three-phase at 460V, the load sits in the bracket between a 70A standard size (non-continuous) and the next size up that covers a continuous load under 210.19(A) (around 80A). The actual install pick depends on whether the load is continuous and the factors above; a conversion page can't pick a single "right" breaker from the amp draw alone.

Energy Cost

42.33 kW costs $7.20/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC three-phase)

How the line current for 42.33 kW at 460V changes with load power factor, on the same AC three-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load Type	PF	42.33 kW at 460V (AC three-phase)
Resistive (heaters, incandescent)	1	53.13 A
Fluorescent lamps	0.95	55.92 A
LED lighting	0.9	59.03 A
Synchronous motors	0.9	59.03 A
Typical mixed loads	0.85	62.5 A
Induction motors (full load)	0.8	66.41 A
Computers (without PFC)	0.65	81.73 A
Induction motors (no load)	0.35	151.79 A

AC Conversion Comparison

On DC, 42.33kW at 460V draws 92.02A. AC single-phase at PF 0.85 pulls 108.25A because reactive current is added on top of the real power. Three-phase at the same voltage needs only 62.5A per line since the same 42.33kW is shared across three conductors instead of one.

Circuit Type	Formula	Result
DC	42,327 ÷ 460	92.02 A
AC Single Phase (PF 0.85)	42,327 ÷ (0.85 × 460)	108.25 A
AC Three Phase (PF 0.85)	42,327 ÷ (1.732 × 0.85 × 460)	62.5 A

Other kW Values at 460V

kW	AC 3-Phase per line, PF 0.85	AC 1-Phase PF 0.85
7.5 kW	11.07 A	19.18 A
8 kW	11.81 A	20.46 A
10 kW	14.77 A	25.58 A
12 kW	17.72 A	30.69 A
15 kW	22.15 A	38.36 A
18 kW	26.58 A	46.04 A
20 kW	29.53 A	51.15 A
22 kW	32.49 A	56.27 A
25 kW	36.91 A	63.94 A
30 kW	44.3 A	76.73 A
35 kW	51.68 A	89.51 A
40 kW	59.06 A	102.3 A
50 kW	73.83 A	127.88 A
60 kW	88.6 A	153.45 A
75 kW	110.74 A	191.82 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

electrical_services 42.33 kW at 208V = 138.22A (3-phase) electrical_services 42.33 kW at 400V = 71.88A (3-phase) electrical_services 42.33 kW at 480V = 59.9A (3-phase) electrical_services 42.33 kW at 575V = 50A (3-phase)

Related Calculations

bolt 42,327W to amps at 460V payments 42,327W running cost cable Wire size for 62.5A at 460V (3Φ)

Frequently Asked Questions

How many amps is 42.33 kW at 460V?expand_more

42.33 kW at 460V draws about 62.5 amps on an AC three-phase circuit at PF 0.85. Alternate cases at the same voltage: 92.02A on DC, 108.25A on AC single-phase.

How does three-phase affect the amps for 42.33 kW?expand_more

Three-phase at 460V draws 62.5A per line versus 108.25A single-phase. Less current per conductor means smaller wire and lower I²R losses.

Why do industrial systems use kW instead of watts?expand_more

Industrial equipment operates at higher power levels. 42.33 kW is easier to express than 42,327W. The math is identical, just scaled by 1000.

What is 42.33 kW in watts?expand_more

42.33 kW equals 42,327 watts. Multiply kilowatts by 1000.

Is 42.33 kW single-phase or three-phase?expand_more

42.33 kW is typically three-phase in commercial and industrial settings.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.