How Many Amps Is 426.36 kW at 460V?

At 460V, 426.36 kW pulls approximately 629.57 amps on AC three-phase (PF 0.85). This is the case typical for commercial HVAC, industrial motors, rooftop units, and three-phase panel loads. Always verify against the equipment nameplate for actual install sizing.

426.36 kW at 460V, AC three-phase (PF 0.85)

629.57 Amps

426.36 kilowatts at 460V on AC three-phase ≈ 629.57 amps

AC Single Phase (PF 0.85)1,090.44 A

DC (ideal baseline)926.87 A

Try: 200kW at 460V 150kW at 460V 125kW at 460V 100kW at 460V

Volts

Amps (AC three-phase, PF 0.85)

629.57

Formulas

DC: kW to Amps

I_(A) = 1000 × P_(kW) ÷ V_(V)

1000 × 426.36 ÷ 460 = 426,362 ÷ 460 = 926.87 A

AC Single Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (PF × V_(V))

426,362 ÷ (0.85 × 460) = 426,362 ÷ 391 = 1,090.44 A

AC Three Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (√3 × PF × V_L-L), where V_L-L is the line-to-line voltage

426,362 ÷ (1.732 × 0.85 × 460) = 426,362 ÷ 677.21 = 629.57 A

Equipment & Circuit Sizing

Energy Cost

426.36 kW costs $72.48/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC three-phase)

How the line current for 426.36 kW at 460V changes with load power factor, on the same AC three-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load Type	PF	426.36 kW at 460V (AC three-phase)
Resistive (heaters, incandescent)	1	535.13 A
Fluorescent lamps	0.95	563.3 A
LED lighting	0.9	594.59 A
Synchronous motors	0.9	594.59 A
Typical mixed loads	0.85	629.57 A
Induction motors (full load)	0.8	668.91 A
Computers (without PFC)	0.65	823.28 A
Induction motors (no load)	0.35	1,528.95 A

AC Conversion Comparison

On DC, 426.36kW at 460V draws 926.87A. AC single-phase at PF 0.85 pulls 1,090.44A because reactive current is added on top of the real power. Three-phase at the same voltage needs only 629.57A per line since the same 426.36kW is shared across three conductors instead of one.

Circuit Type	Formula	Result
DC	426,362 ÷ 460	926.87 A
AC Single Phase (PF 0.85)	426,362 ÷ (0.85 × 460)	1,090.44 A
AC Three Phase (PF 0.85)	426,362 ÷ (1.732 × 0.85 × 460)	629.57 A

Other kW Values at 460V

kW	AC 3-Phase per line, PF 0.85	AC 1-Phase PF 0.85
15 kW	22.15 A	38.36 A
18 kW	26.58 A	46.04 A
20 kW	29.53 A	51.15 A
22 kW	32.49 A	56.27 A
25 kW	36.91 A	63.94 A
30 kW	44.3 A	76.73 A
35 kW	51.68 A	89.51 A
40 kW	59.06 A	102.3 A
50 kW	73.83 A	127.88 A
60 kW	88.6 A	153.45 A
75 kW	110.74 A	191.82 A
100 kW	147.66 A	255.75 A
125 kW	184.57 A	319.69 A
150 kW	221.49 A	383.63 A
200 kW	295.32 A	511.51 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

electrical_services 426.36 kW at 208V = 1,392.31A (3-phase) electrical_services 426.36 kW at 400V = 724A (3-phase) electrical_services 426.36 kW at 480V = 603.33A (3-phase) electrical_services 426.36 kW at 575V = 503.65A (3-phase)

Related Calculations

bolt 426,362W to amps at 460V payments 426,362W running cost cable Wire size for 629.57A at 460V (3Φ)

Frequently Asked Questions

How many amps is 426.36 kW at 460V?expand_more

426.36 kW at 460V draws about 629.57 amps on an AC three-phase circuit at PF 0.85. Alternate cases at the same voltage: 926.87A on DC, 1,090.44A on AC single-phase.

What is 426.36 kW in watts?expand_more

426.36 kW equals 426,362 watts. Multiply kilowatts by 1000.

How does three-phase affect the amps for 426.36 kW?expand_more

Three-phase at 460V draws 629.57A per line versus 1,090.44A single-phase. Less current per conductor means smaller wire and lower I²R losses.

What size breaker would I need for 426.36 kW at 460V?expand_more

This is a sizing question, not a conversion question, and there is no single correct answer from a page like this. Breaker selection depends on the equipment nameplate FLA, whether the load is continuous (NEC 210.19(A) applies the 125% continuous-load rule), the conductor ampacity and temperature rating, any NEC 430/440 motor or HVAC provisions, and local code interpretation. Use the nameplate and a licensed electrician for the real install value; use this page only for the current-draw estimate that feeds into that process.

Why do industrial systems use kW instead of watts?expand_more

Industrial equipment operates at higher power levels. 426.36 kW is easier to express than 426,362W. The math is identical, just scaled by 1000.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.