How Many Amps Is 429 kW at 480V?

429 kW at 480V draws about 607.07 amps on an AC three-phase circuit at PF 0.85, typical for commercial HVAC, industrial motors, rooftop units, and three-phase panel loads. Actual current varies with equipment power factor and duty cycle.

429 kW at 480V, AC three-phase (PF 0.85)
607.07 Amps
429 kilowatts at 480V on AC three-phase ≈ 607.07 amps
AC Single Phase (PF 0.85)1,051.47 A
DC (ideal baseline)893.75 A
607.07

Formulas

DC: kW to Amps

I(A) = 1000 × P(kW) ÷ V(V)

1000 × 429 ÷ 480 = 429,000 ÷ 480 = 893.75 A

AC Single Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (PF × V(V))

429,000 ÷ (0.85 × 480) = 429,000 ÷ 408 = 1,051.47 A

AC Three Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (√3 × PF × VL-L), where VL-L is the line-to-line voltage

429,000 ÷ (1.732 × 0.85 × 480) = 429,000 ÷ 706.66 = 607.07 A

Equipment & Circuit Sizing

Energy Cost

429 kW costs $72.93/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC three-phase)

How the line current for 429 kW at 480V changes with load power factor, on the same AC three-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load TypePF429 kW at 480V (AC three-phase)
Resistive (heaters, incandescent)1516.01 A
Fluorescent lamps0.95543.17 A
LED lighting0.9573.34 A
Synchronous motors0.9573.34 A
Typical mixed loads0.85607.07 A
Induction motors (full load)0.8645.01 A
Computers (without PFC)0.65793.86 A
Induction motors (no load)0.351,474.31 A

AC Conversion Comparison

On DC, 429kW at 480V draws 893.75A. AC single-phase at PF 0.85 pulls 1,051.47A because reactive current is added on top of the real power. Three-phase at the same voltage needs only 607.07A per line since the same 429kW is shared across three conductors instead of one.

Circuit TypeFormulaResult
DC429,000 ÷ 480893.75 A
AC Single Phase (PF 0.85)429,000 ÷ (0.85 × 480)1,051.47 A
AC Three Phase (PF 0.85)429,000 ÷ (1.732 × 0.85 × 480)607.07 A

Other kW Values at 480V

kWAC 3-Phase per line, PF 0.85AC 1-Phase PF 0.85
15 kW21.23 A36.76 A
18 kW25.47 A44.12 A
20 kW28.3 A49.02 A
22 kW31.13 A53.92 A
25 kW35.38 A61.27 A
30 kW42.45 A73.53 A
35 kW49.53 A85.78 A
40 kW56.6 A98.04 A
50 kW70.75 A122.55 A
60 kW84.9 A147.06 A
75 kW106.13 A183.82 A
100 kW141.51 A245.1 A
125 kW176.88 A306.37 A
150 kW212.26 A367.65 A
200 kW283.01 A490.2 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

Frequently Asked Questions

429 kW at 480V draws about 607.07 amps on an AC three-phase circuit at PF 0.85. Alternate cases at the same voltage: 893.75A on DC, 1,051.47A on AC single-phase.
DC: Amps = (kW × 1000) ÷ Volts. AC single-phase: Amps = (kW × 1000) ÷ (Volts × PF). AC three-phase: Amps = (kW × 1000) ÷ (VoltsL-L × √3 × PF).
480V is commercial/industrial panel voltage, not a typical AC EVSE feed to a vehicle. On three-phase 480V, 429 kW works out to about 607.07A per line (three-phase at PF 0.85). In practice, 400-480V three-phase is usually the AC input to a DC fast charger (50-350 kW CCS/NACS stations like Tesla Superchargers), which rectifies to DC and delivers that directly to the vehicle, rather than an AC EVSE connector. A 429 kW figure at 480V is most likely the AC feed to a smaller commercial cabinet or the control-side input of a larger DC fast charger, not an at-the-car AC current.
429 kW is typically three-phase in commercial and industrial settings.
429 kW equals 429,000 watts. Multiply kilowatts by 1000.
This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.