How Many Amps Is 465 kW at 480V?

465 kW at 480V draws about 658.01 amps on an AC three-phase circuit at PF 0.85, typical for commercial HVAC, industrial motors, rooftop units, and three-phase panel loads. Actual current varies with equipment power factor and duty cycle.

465 kW at 480V, AC three-phase (PF 0.85)
658.01 Amps
465 kilowatts at 480V on AC three-phase ≈ 658.01 amps
AC Single Phase (PF 0.85)1,139.71 A
DC (ideal baseline)968.75 A
658.01

Formulas

DC: kW to Amps

I(A) = 1000 × P(kW) ÷ V(V)

1000 × 465 ÷ 480 = 465,000 ÷ 480 = 968.75 A

AC Single Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (PF × V(V))

465,000 ÷ (0.85 × 480) = 465,000 ÷ 408 = 1,139.71 A

AC Three Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (√3 × PF × VL-L), where VL-L is the line-to-line voltage

465,000 ÷ (1.732 × 0.85 × 480) = 465,000 ÷ 706.66 = 658.01 A

Equipment & Circuit Sizing

Energy Cost

465 kW costs $79.05/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC three-phase)

How the line current for 465 kW at 480V changes with load power factor, on the same AC three-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load TypePF465 kW at 480V (AC three-phase)
Resistive (heaters, incandescent)1559.31 A
Fluorescent lamps0.95588.75 A
LED lighting0.9621.45 A
Synchronous motors0.9621.45 A
Typical mixed loads0.85658.01 A
Induction motors (full load)0.8699.14 A
Computers (without PFC)0.65860.47 A
Induction motors (no load)0.351,598.02 A

AC Conversion Comparison

On DC, 465kW at 480V draws 968.75A. AC single-phase at PF 0.85 pulls 1,139.71A because reactive current is added on top of the real power. Three-phase at the same voltage needs only 658.01A per line since the same 465kW is shared across three conductors instead of one.

Circuit TypeFormulaResult
DC465,000 ÷ 480968.75 A
AC Single Phase (PF 0.85)465,000 ÷ (0.85 × 480)1,139.71 A
AC Three Phase (PF 0.85)465,000 ÷ (1.732 × 0.85 × 480)658.01 A

Other kW Values at 480V

kWAC 3-Phase per line, PF 0.85AC 1-Phase PF 0.85
15 kW21.23 A36.76 A
18 kW25.47 A44.12 A
20 kW28.3 A49.02 A
22 kW31.13 A53.92 A
25 kW35.38 A61.27 A
30 kW42.45 A73.53 A
35 kW49.53 A85.78 A
40 kW56.6 A98.04 A
50 kW70.75 A122.55 A
60 kW84.9 A147.06 A
75 kW106.13 A183.82 A
100 kW141.51 A245.1 A
125 kW176.88 A306.37 A
150 kW212.26 A367.65 A
200 kW283.01 A490.2 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

Frequently Asked Questions

465 kW at 480V draws about 658.01 amps on an AC three-phase circuit at PF 0.85. Alternate cases at the same voltage: 968.75A on DC, 1,139.71A on AC single-phase.
465 kW is typically three-phase in commercial and industrial settings.
465 kW costs $79.05 per hour at $0.17/kWh (US residential average, last reviewed April 2026). At 8 hours/day that is $18,972.00 per month.
Industrial equipment operates at higher power levels. 465 kW is easier to express than 465,000W. The math is identical, just scaled by 1000.
Three-phase at 480V draws 658.01A per line versus 1,139.71A single-phase. Less current per conductor means smaller wire and lower I²R losses.
This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.