How Many Amps Is 5.89 kW at 100V?

5.89 kilowatts at 100V works out to roughly 69.28 amps on AC single-phase at PF 0.85. That is typical for residential water heaters, dryers, ranges, EV chargers, and HVAC equipment. See the DC and alternate-phase numbers below for other circuit types.

5.89 kW at 100V, AC single-phase (PF 0.85)

69.28 Amps

5.89 kilowatts at 100V on AC single-phase ≈ 69.28 amps

DC (ideal baseline)58.89 A

Try: 6kW at 100V 5kW at 100V 7.5kW at 100V 4kW at 100V

Volts

Amps (AC single-phase, PF 0.85)

69.28

Formulas

DC: kW to Amps

I_(A) = 1000 × P_(kW) ÷ V_(V)

1000 × 5.89 ÷ 100 = 5,889 ÷ 100 = 58.89 A

AC Single Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (PF × V_(V))

5,889 ÷ (0.85 × 100) = 5,889 ÷ 85 = 69.28 A

Equipment & Circuit Sizing

Breaker Sizing

Breaker ratings are in amps, not watts, so the real install answer depends on the equipment nameplate FLA, whether the load is continuous (NEC 210.19(A) sizes the conductor and OCP at 125% of a continuous load, equivalently 80% of breaker rating), conductor ampacity and temperature rating, ambient and bundling derates, and any motor or HVAC provisions (NEC 430 / 440). At roughly 69.28A on AC single-phase at 100V, the load sits in the bracket between a 70A standard size (non-continuous) and the next size up that covers a continuous load under 210.19(A) (around 90A). The actual install pick depends on whether the load is continuous and the factors above; a conversion page can't pick a single "right" breaker from the amp draw alone.

Energy Cost

5.89 kW costs $1.00/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC single-phase)

How the line current for 5.89 kW at 100V changes with load power factor, on the same AC single-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load Type	PF	5.89 kW at 100V (AC single-phase)
Resistive (heaters, incandescent)	1	58.89 A
Fluorescent lamps	0.95	61.99 A
LED lighting	0.9	65.43 A
Synchronous motors	0.9	65.43 A
Typical mixed loads	0.85	69.28 A
Induction motors (full load)	0.8	73.61 A
Computers (without PFC)	0.65	90.6 A
Induction motors (no load)	0.35	168.26 A

AC Conversion Comparison

On DC, 5.89kW at 100V draws 58.89A. AC single-phase at PF 0.85 pulls 69.28A because reactive current is added on top of the real power.

Circuit Type	Formula	Result
DC	5,889 ÷ 100	58.89 A
AC Single Phase (PF 0.85)	5,889 ÷ (0.85 × 100)	69.28 A

Other kW Values at 100V

kW	AC 1-Phase PF 0.85	DC Amps PF 1.0 baseline
0.5 kW	5.88 A	5 A
0.75 kW	8.82 A	7.5 A
1 kW	11.76 A	10 A
1.5 kW	17.65 A	15 A
2 kW	23.53 A	20 A
2.5 kW	29.41 A	25 A
3 kW	35.29 A	30 A
3.5 kW	41.18 A	35 A
4 kW	47.06 A	40 A
5 kW	58.82 A	50 A
6 kW	70.59 A	60 A
7.5 kW	88.24 A	75 A
8 kW	94.12 A	80 A
10 kW	117.65 A	100 A
12 kW	141.18 A	120 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

Related Calculations

bolt 5,889W to amps at 100V payments 5,889W running cost cable Wire size for 69.28A at 100V

Frequently Asked Questions

How many amps is 5.89 kW at 100V?expand_more

5.89 kW at 100V draws about 69.28 amps on an AC single-phase circuit at PF 0.85. Alternate cases at the same voltage: 58.89A on DC.

Is 5.89 kW single-phase or three-phase?expand_more

5.89 kW is available in both, but three-phase is more common for commercial HVAC, rooftop units, and motors once you reach this range.

How much does 5.89 kW cost to run?expand_more

5.89 kW costs $1.00 per hour at $0.17/kWh (US residential average, last reviewed April 2026). At 8 hours/day that is $240.27 per month.

How many amps does a 5.89 kW EV charger draw at 100V?expand_more

At 100V, this is Level 1 territory (120V AC, single-phase, typically 12-16A). A 5.89 kW draw on a standard 120V household outlet is at or above the 1,440W NEC 210.19(A) continuous figure, which is why Level 1 EVSE ships at 1.4-1.9 kW and takes 20+ hours for a full charge. If you need 5.89 kW of charging, you want Level 2 on a 240V dedicated circuit, not 120V.

What is 5.89 kW in watts?expand_more

5.89 kW equals 5,889 watts. Multiply kilowatts by 1000.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.