How Many Amps Is 680 kW at 575V?

At 575V, 680 kW pulls approximately 803.27 amps on AC three-phase (PF 0.85). This is the case typical for commercial HVAC, industrial motors, rooftop units, and three-phase panel loads. Always verify against the equipment nameplate for actual install sizing.

680 kW at 575V, AC three-phase (PF 0.85)
803.27 Amps
680 kilowatts at 575V on AC three-phase ≈ 803.27 amps
AC Single Phase (PF 0.85)1,391.3 A
DC (ideal baseline)1,182.61 A
803.27

Formulas

DC: kW to Amps

I(A) = 1000 × P(kW) ÷ V(V)

1000 × 680 ÷ 575 = 680,000 ÷ 575 = 1,182.61 A

AC Single Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (PF × V(V))

680,000 ÷ (0.85 × 575) = 680,000 ÷ 488.75 = 1,391.3 A

AC Three Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (√3 × PF × VL-L), where VL-L is the line-to-line voltage

680,000 ÷ (1.732 × 0.85 × 575) = 680,000 ÷ 846.52 = 803.27 A

Equipment & Circuit Sizing

Energy Cost

680 kW costs $115.60/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC three-phase)

How the line current for 680 kW at 575V changes with load power factor, on the same AC three-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load TypePF680 kW at 575V (AC three-phase)
Resistive (heaters, incandescent)1682.78 A
Fluorescent lamps0.95718.72 A
LED lighting0.9758.64 A
Synchronous motors0.9758.64 A
Typical mixed loads0.85803.27 A
Induction motors (full load)0.8853.47 A
Computers (without PFC)0.651,050.43 A
Induction motors (no load)0.351,950.8 A

AC Conversion Comparison

On DC, 680kW at 575V draws 1,182.61A. AC single-phase at PF 0.85 pulls 1,391.3A because reactive current is added on top of the real power. Three-phase at the same voltage needs only 803.27A per line since the same 680kW is shared across three conductors instead of one.

Circuit TypeFormulaResult
DC680,000 ÷ 5751,182.61 A
AC Single Phase (PF 0.85)680,000 ÷ (0.85 × 575)1,391.3 A
AC Three Phase (PF 0.85)680,000 ÷ (1.732 × 0.85 × 575)803.27 A

Other kW Values at 575V

kWAC 3-Phase per line, PF 0.85AC 1-Phase PF 0.85
15 kW17.72 A30.69 A
18 kW21.26 A36.83 A
20 kW23.63 A40.92 A
22 kW25.99 A45.01 A
25 kW29.53 A51.15 A
30 kW35.44 A61.38 A
35 kW41.34 A71.61 A
40 kW47.25 A81.84 A
50 kW59.06 A102.3 A
60 kW70.88 A122.76 A
75 kW88.6 A153.45 A
100 kW118.13 A204.6 A
125 kW147.66 A255.75 A
150 kW177.19 A306.91 A
200 kW236.26 A409.21 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

Frequently Asked Questions

680 kW at 575V draws about 803.27 amps on an AC three-phase circuit at PF 0.85. Alternate cases at the same voltage: 1,182.61A on DC, 1,391.3A on AC single-phase.
680 kW costs $115.60 per hour at $0.17/kWh (US residential average, last reviewed April 2026). At 8 hours/day that is $27,744.00 per month.
680 kW is typically three-phase in commercial and industrial settings.
Three-phase at 575V draws 803.27A per line versus 1,391.3A single-phase. Less current per conductor means smaller wire and lower I²R losses.
DC: Amps = (kW × 1000) ÷ Volts. AC single-phase: Amps = (kW × 1000) ÷ (Volts × PF). AC three-phase: Amps = (kW × 1000) ÷ (VoltsL-L × √3 × PF).
This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.