How Many Amps Is 717.6 kW at 480V?

717.6 kW at 480V draws about 1,015.46 amps on an AC three-phase circuit at PF 0.85, typical for commercial HVAC, industrial motors, rooftop units, and three-phase panel loads. Actual current varies with equipment power factor and duty cycle.

717.6 kW at 480V, AC three-phase (PF 0.85)
1,015.46 Amps
717.6 kilowatts at 480V on AC three-phase ≈ 1,015.46 amps
AC Single Phase (PF 0.85)1,758.82 A
DC (ideal baseline)1,495 A
1,015.46

Formulas

DC: kW to Amps

I(A) = 1000 × P(kW) ÷ V(V)

1000 × 717.6 ÷ 480 = 717,600 ÷ 480 = 1,495 A

AC Single Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (PF × V(V))

717,600 ÷ (0.85 × 480) = 717,600 ÷ 408 = 1,758.82 A

AC Three Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (√3 × PF × VL-L), where VL-L is the line-to-line voltage

717,600 ÷ (1.732 × 0.85 × 480) = 717,600 ÷ 706.66 = 1,015.46 A

Equipment & Circuit Sizing

Energy Cost

717.6 kW costs $121.99/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC three-phase)

How the line current for 717.6 kW at 480V changes with load power factor, on the same AC three-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load TypePF717.6 kW at 480V (AC three-phase)
Resistive (heaters, incandescent)1863.14 A
Fluorescent lamps0.95908.57 A
LED lighting0.9959.04 A
Synchronous motors0.9959.04 A
Typical mixed loads0.851,015.46 A
Induction motors (full load)0.81,078.92 A
Computers (without PFC)0.651,327.91 A
Induction motors (no load)0.352,466.11 A

AC Conversion Comparison

On DC, 717.6kW at 480V draws 1,495A. AC single-phase at PF 0.85 pulls 1,758.82A because reactive current is added on top of the real power. Three-phase at the same voltage needs only 1,015.46A per line since the same 717.6kW is shared across three conductors instead of one.

Circuit TypeFormulaResult
DC717,600 ÷ 4801,495 A
AC Single Phase (PF 0.85)717,600 ÷ (0.85 × 480)1,758.82 A
AC Three Phase (PF 0.85)717,600 ÷ (1.732 × 0.85 × 480)1,015.46 A

Other kW Values at 480V

kWAC 3-Phase per line, PF 0.85AC 1-Phase PF 0.85
15 kW21.23 A36.76 A
18 kW25.47 A44.12 A
20 kW28.3 A49.02 A
22 kW31.13 A53.92 A
25 kW35.38 A61.27 A
30 kW42.45 A73.53 A
35 kW49.53 A85.78 A
40 kW56.6 A98.04 A
50 kW70.75 A122.55 A
60 kW84.9 A147.06 A
75 kW106.13 A183.82 A
100 kW141.51 A245.1 A
125 kW176.88 A306.37 A
150 kW212.26 A367.65 A
200 kW283.01 A490.2 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

Frequently Asked Questions

717.6 kW at 480V draws about 1,015.46 amps on an AC three-phase circuit at PF 0.85. Alternate cases at the same voltage: 1,495A on DC, 1,758.82A on AC single-phase.
DC: Amps = (kW × 1000) ÷ Volts. AC single-phase: Amps = (kW × 1000) ÷ (Volts × PF). AC three-phase: Amps = (kW × 1000) ÷ (VoltsL-L × √3 × PF).
717.6 kW equals 717,600 watts. Multiply kilowatts by 1000.
Three-phase at 480V draws 1,015.46A per line versus 1,758.82A single-phase. Less current per conductor means smaller wire and lower I²R losses.
717.6 kW is typically three-phase in commercial and industrial settings.
This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.