How Many Amps Is 772 kW at 575V?

772 kW at 575V draws about 911.95 amps on an AC three-phase circuit at PF 0.85, typical for commercial HVAC, industrial motors, rooftop units, and three-phase panel loads. Actual current varies with equipment power factor and duty cycle.

772 kW at 575V, AC three-phase (PF 0.85)
911.95 Amps
772 kilowatts at 575V on AC three-phase ≈ 911.95 amps
AC Single Phase (PF 0.85)1,579.54 A
DC (ideal baseline)1,342.61 A
911.95

Formulas

DC: kW to Amps

I(A) = 1000 × P(kW) ÷ V(V)

1000 × 772 ÷ 575 = 772,000 ÷ 575 = 1,342.61 A

AC Single Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (PF × V(V))

772,000 ÷ (0.85 × 575) = 772,000 ÷ 488.75 = 1,579.54 A

AC Three Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (√3 × PF × VL-L), where VL-L is the line-to-line voltage

772,000 ÷ (1.732 × 0.85 × 575) = 772,000 ÷ 846.52 = 911.95 A

Equipment & Circuit Sizing

Energy Cost

772 kW costs $131.24/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC three-phase)

How the line current for 772 kW at 575V changes with load power factor, on the same AC three-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load TypePF772 kW at 575V (AC three-phase)
Resistive (heaters, incandescent)1775.16 A
Fluorescent lamps0.95815.95 A
LED lighting0.9861.28 A
Synchronous motors0.9861.28 A
Typical mixed loads0.85911.95 A
Induction motors (full load)0.8968.94 A
Computers (without PFC)0.651,192.55 A
Induction motors (no load)0.352,214.73 A

AC Conversion Comparison

On DC, 772kW at 575V draws 1,342.61A. AC single-phase at PF 0.85 pulls 1,579.54A because reactive current is added on top of the real power. Three-phase at the same voltage needs only 911.95A per line since the same 772kW is shared across three conductors instead of one.

Circuit TypeFormulaResult
DC772,000 ÷ 5751,342.61 A
AC Single Phase (PF 0.85)772,000 ÷ (0.85 × 575)1,579.54 A
AC Three Phase (PF 0.85)772,000 ÷ (1.732 × 0.85 × 575)911.95 A

Other kW Values at 575V

kWAC 3-Phase per line, PF 0.85AC 1-Phase PF 0.85
15 kW17.72 A30.69 A
18 kW21.26 A36.83 A
20 kW23.63 A40.92 A
22 kW25.99 A45.01 A
25 kW29.53 A51.15 A
30 kW35.44 A61.38 A
35 kW41.34 A71.61 A
40 kW47.25 A81.84 A
50 kW59.06 A102.3 A
60 kW70.88 A122.76 A
75 kW88.6 A153.45 A
100 kW118.13 A204.6 A
125 kW147.66 A255.75 A
150 kW177.19 A306.91 A
200 kW236.26 A409.21 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

Frequently Asked Questions

772 kW at 575V draws about 911.95 amps on an AC three-phase circuit at PF 0.85. Alternate cases at the same voltage: 1,342.61A on DC, 1,579.54A on AC single-phase.
772 kW equals 772,000 watts. Multiply kilowatts by 1000.
DC: Amps = (kW × 1000) ÷ Volts. AC single-phase: Amps = (kW × 1000) ÷ (Volts × PF). AC three-phase: Amps = (kW × 1000) ÷ (VoltsL-L × √3 × PF).
772 kW is typically three-phase in commercial and industrial settings.
Three-phase at 575V draws 911.95A per line versus 1,579.54A single-phase. Less current per conductor means smaller wire and lower I²R losses.
This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.