What Is the Voltage Drop for 10 AWG at 7A and 50 Feet?

10 AWG copper carrying 7 amps over 50 feet on a single-phase / DC circuit drops 0.868 volts (0.7233% on a 120V source). This sits within the 3% branch target and the 5% feeder+branch total target that NEC 210.19(A) Informational Note 4 cites. Both are planning targets, not code requirements.

10 AWG, 7A, 50ft · single-phase / DC

0.868 V drop (0.7233% on 120V)

On 120V circuit0.7233%

On 240V circuit0.3617%

Circuit basis: This uses the single-phase / DC round-trip formula (factor of 2) for the voltage drop across the two circuit conductors. For a three-phase line-to-line run use the three-phase version of the page (append ?type=3ph). Switch to the three-phase version →

Gauge

10 AWG

Amps

Feet

Drop @ 120V

0.87V (0.72%)

Assumes a 120V source on a single-phase / DC circuit. Use the circuit-basis link above to switch between single-phase/DC and three-phase.

Voltage Drop Formula (single-phase / DC)

V_drop = (2 × L × I × R) ÷ 1000

(2 × 50 × 7 × 1.24) ÷ 1000 = 0.868 V

DC and single-phase AC use the round-trip factor of 2. Current travels out to the load on one conductor and returns on another.

For a three-phase circuit at the same amps and distance, see the three-phase version (uses √3 instead of 2, so the drop is about 13.4% lower).

Percentage

%VD = (V_drop ÷ V_source) × 100

On 120V: (0.868 ÷ 120) × 100 = 0.7233%

On 240V: (0.868 ÷ 240) × 100 = 0.3617%

How This Estimate Changes with Run Length and Gauge

Gauge Check

10 AWG clears the 3% drop target at these inputs. A smaller conductor may also meet it with less margin. See the minimum gauge for this load and distance.

Impact of Distance

Voltage drop is proportional to distance. Here is 10 AWG at 7A at different distances:

Distance	Drop (V)	% on 120V	% on 240V	NEC (120V)
25ft	0.434V	0.3617%	0.1808%	OK
50ft	0.868V	0.7233%	0.3617%	OK
75ft	1.3V	1.09%	0.5425%	OK
100ft	1.74V	1.45%	0.7233%	OK
150ft	2.6V	2.17%	1.09%	OK
200ft	3.47V	2.89%	1.45%	OK
300ft	5.21V	4.34%	2.17%	Caution

Same Run, Different Wire Gauges

How does wire gauge affect voltage drop for 7A at 50 feet on 120V single-phase / DC? Only gauges whose branch-circuit OCP cap is at or above the 7A load are listed, since thinner gauges would fail the ampacity check before drop even matters.

Gauge	Drop (V)	% on 120V	% on 240V	3% Target (120V)
10 AWG	0.868V	0.7233%	0.3617%	OK
8 AWG	0.5446V	0.4538%	0.2269%	OK
6 AWG	0.3437V	0.2864%	0.1432%	OK
4 AWG	0.2156V	0.1797%	0.0898%	OK
3 AWG	0.1715V	0.1429%	0.0715%	OK
2 AWG	0.1358V	0.1132%	0.0566%	OK

Related Calculations

cable Wire size: 7A, 50ft bolt Watts to amps calculator functions Voltage drop formula

Frequently Asked Questions

What is the voltage drop for 10 AWG at 7A and 50ft?expand_more

10 AWG carrying 7A over 50ft has a 0.868V drop (0.7233% on 120V). Reference: 0.3617% on 240V.

Does 10 AWG meet the 3% drop target at 7A and 50ft on 120V?expand_more

On 120V, this run sits at 0.7233%, which is within the 3% branch and 5% feeder+branch total drop targets. NEC 210.19(A) Informational Note 4 cites 3% for branch circuits and 5% for total feeder+branch drop as performance recommendations, not hard code requirements.

Does wire material affect voltage drop?expand_more

Yes. Aluminum has roughly 1.3 to 1.4 times the resistance of copper at the NEC Chapter 9 Table 8 75°C reference temperature, so for the same voltage drop an aluminum conductor is typically one to two gauges larger than copper. The exact gap depends on whether ampacity or voltage drop is binding, and the install still needs anti-oxidant compound and aluminum-rated lugs.

What happens if voltage drop is too high?expand_more

Motors run hotter and can have trouble starting under load. Incandescent and halogen lighting dims. Some electronics misbehave at the low end of their input tolerance. Energy is wasted as I²R heating in the conductor. These are performance issues; high drop is not itself a code violation unless the specific installation cites a hard limit.

What wire gauge should I use instead of 10 AWG for this run?expand_more

10 AWG already sits within the 3% branch-circuit drop target at these inputs (0.7233% on 120V). Going to a larger gauge is only useful if you want more headroom for future load growth, longer runs, or tighter drop targets like the 5% feeder+branch total recommendation used in sensitive or motor-heavy installations.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.