What Is the Voltage Drop for 8 AWG at 15A and 100 Feet?

Running 15A through 8 AWG copper for 100 feet on a single-phase / DC circuit produces a 2.33-volt drop. On a 120V source that is 1.95%; on 240V it is 0.9725%. NEC 210.19(A) Informational Note 4 recommends keeping branch-circuit drop at or below 3% and total feeder+branch drop at or below 5%, these are performance recommendations, not code requirements.

8 AWG, 15A, 100ft · single-phase / DC

2.33 V drop (1.95% on 120V)

On 120V circuit1.95%

On 240V circuit0.9725%

Circuit basis: This uses the single-phase / DC round-trip formula (factor of 2) for the voltage drop across the two circuit conductors. For a three-phase line-to-line run use the three-phase version of the page (append ?type=3ph). Switch to the three-phase version →

Gauge

8 AWG

Amps

Feet

Drop @ 120V

2.33V (1.95%)

Assumes a 120V source on a single-phase / DC circuit. Use the circuit-basis link above to switch between single-phase/DC and three-phase.

Voltage Drop Formula (single-phase / DC)

V_drop = (2 × L × I × R) ÷ 1000

(2 × 100 × 15 × 0.778) ÷ 1000 = 2.33 V

DC and single-phase AC use the round-trip factor of 2. Current travels out to the load on one conductor and returns on another.

For a three-phase circuit at the same amps and distance, see the three-phase version (uses √3 instead of 2, so the drop is about 13.4% lower).

Percentage

%VD = (V_drop ÷ V_source) × 100

On 120V: (2.33 ÷ 120) × 100 = 1.95%

On 240V: (2.33 ÷ 240) × 100 = 0.9725%

How This Estimate Changes with Run Length and Gauge

Gauge Check

8 AWG clears the 3% drop target at these inputs. A smaller conductor may also meet it with less margin. See the minimum gauge for this load and distance.

Impact of Distance

Voltage drop is proportional to distance. Here is 8 AWG at 15A at different distances:

Distance	Drop (V)	% on 120V	% on 240V	NEC (120V)
25ft	0.5835V	0.4863%	0.2431%	OK
50ft	1.17V	0.9725%	0.4863%	OK
75ft	1.75V	1.46%	0.7294%	OK
100ft	2.33V	1.95%	0.9725%	OK
150ft	3.5V	2.92%	1.46%	OK
200ft	4.67V	3.89%	1.95%	Caution
300ft	7V	5.84%	2.92%	Past 5%

Same Run, Different Wire Gauges

How does wire gauge affect voltage drop for 15A at 100 feet on 120V single-phase / DC? Only gauges whose branch-circuit OCP cap is at or above the 15A load are listed, since thinner gauges would fail the ampacity check before drop even matters.

Gauge	Drop (V)	% on 120V	% on 240V	3% Target (120V)
8 AWG	2.33V	1.95%	0.9725%	OK
6 AWG	1.47V	1.23%	0.6138%	OK
4 AWG	0.924V	0.77%	0.385%	OK
3 AWG	0.735V	0.6125%	0.3063%	OK
2 AWG	0.582V	0.485%	0.2425%	OK
1 AWG	0.462V	0.385%	0.1925%	OK

Related Calculations

cable Wire size: 15A, 100ft bolt Watts to amps calculator functions Voltage drop formula

Frequently Asked Questions

What is the voltage drop for 8 AWG at 15A and 100ft?expand_more

8 AWG carrying 15A over 100ft has a 2.33V drop (1.95% on 120V). Reference: 0.9725% on 240V.

Why does distance affect voltage drop?expand_more

Voltage drop is proportional to distance. The formula multiplies by 2 × the distance (out and back). Doubling the run doubles the drop.

Does 8 AWG meet the 3% drop target at 15A and 100ft on 120V?expand_more

On 120V, this run sits at 1.95%, which is within the 3% branch and 5% feeder+branch total drop targets. NEC 210.19(A) Informational Note 4 cites 3% for branch circuits and 5% for total feeder+branch drop as performance recommendations, not hard code requirements.

What wire gauge should I use instead of 8 AWG for this run?expand_more

8 AWG already sits within the 3% branch-circuit drop target at these inputs (1.95% on 120V). Going to a larger gauge is only useful if you want more headroom for future load growth, longer runs, or tighter drop targets like the 5% feeder+branch total recommendation used in sensitive or motor-heavy installations.

Is voltage drop worse on 120V or 240V?expand_more

Same wire, same amps, same distance: the volts dropped are identical. But the percentage is worse on 120V because the drop is a larger fraction of the source voltage. This run would be 0.9725% on 240V versus 1.95% on 120V.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.