8 AWG at 60A and 100 Feet: Ampacity-Invalid Reference Calculation

Reference voltage-drop calculation only. 8 AWG is NEC-capped at 50A branch-circuit OCP per NEC 240.4(D) (75°C ampacity 50A), so 60A on this gauge fails the ampacity check before voltage drop ever enters the conversation. Do not use the number below as an install spec. The 9.34-volt reference drop at 60A through 8 AWG for 100 feet is still a valid I×R calculation across the conductor, which is why this page renders it, but it is a reference-only figure and not a permission slip to run that current on that gauge.

8 AWG, 60A, 100ft · single-phase / DC · reference only, ampacity-invalid

9.34 V drop (7.78% on 120V)

On 120V circuit7.78%

On 240V circuit3.89%

Circuit basis: This uses the single-phase / DC round-trip formula (factor of 2) for the voltage drop across the two circuit conductors. For a three-phase line-to-line run use the three-phase version of the page (append ?type=3ph). Switch to the three-phase version →

Gauge

8 AWG

Amps

Feet

Drop @ 120V

9.34V (7.78%)

Assumes a 120V source on a single-phase / DC circuit. Use the circuit-basis link above to switch between single-phase/DC and three-phase.

Voltage Drop Formula (single-phase / DC)

V_drop = (2 × L × I × R) ÷ 1000

(2 × 100 × 60 × 0.778) ÷ 1000 = 9.34 V

DC and single-phase AC use the round-trip factor of 2. Current travels out to the load on one conductor and returns on another.

For a three-phase circuit at the same amps and distance, see the three-phase version (uses √3 instead of 2, so the drop is about 13.4% lower).

Percentage

%VD = (V_drop ÷ V_source) × 100

On 120V: (9.34 ÷ 120) × 100 = 7.78%

On 240V: (9.34 ÷ 240) × 100 = 3.89%

How This Estimate Changes with Run Length and Gauge

Gauge That Meets the 3% Target

8 AWG can't carry the 60A load in the first place, its branch-circuit OCP cap is 50A under typical conditions. The smallest gauge in our table that clears both the ampacity cap and the 3% drop target at these inputs is 3 AWG. Run the full wire-size calculator for run length, material, and drop-target variations.

Impact of Distance

Voltage drop is proportional to distance. Here is 8 AWG at 60A at different distances:

Distance	Drop (V)	% on 120V	% on 240V	NEC (120V)
25ft	2.33V	1.95%	0.9725%	OK
50ft	4.67V	3.89%	1.95%	Caution
75ft	7V	5.84%	2.92%	Past 5%
100ft	9.34V	7.78%	3.89%	Past 5%
150ft	14V	11.67%	5.84%	Past 5%
200ft	18.67V	15.56%	7.78%	Past 5%
300ft	28.01V	23.34%	11.67%	Past 5%

Same Run, Different Wire Gauges

How does wire gauge affect voltage drop for 60A at 100 feet on 120V single-phase / DC? Only gauges whose branch-circuit OCP cap is at or above the 60A load are listed, since thinner gauges would fail the ampacity check before drop even matters.

Gauge	Drop (V)	% on 120V	% on 240V	3% Target (120V)
6 AWG	5.89V	4.91%	2.46%	Caution
4 AWG	3.7V	3.08%	1.54%	Caution
3 AWG	2.94V	2.45%	1.23%	OK
2 AWG	2.33V	1.94%	0.97%	OK
1 AWG	1.85V	1.54%	0.77%	OK
1/0 AWG	1.46V	1.22%	0.61%	OK
2/0 AWG	1.16V	0.967%	0.4835%	OK
3/0 AWG	0.9192V	0.766%	0.383%	OK
4/0 AWG	0.7296V	0.608%	0.304%	OK
250 kcmil	0.618V	0.515%	0.2575%	OK
300 kcmil	0.5148V	0.429%	0.2145%	OK
350 kcmil	0.4404V	0.367%	0.1835%	OK
500 kcmil	0.3096V	0.258%	0.129%	OK
750 kcmil	0.2052V	0.171%	0.0855%	OK

Related Calculations

cable Wire size: 60A, 100ft bolt Watts to amps calculator functions Voltage drop formula

Frequently Asked Questions

What is the voltage drop for 8 AWG at 60A and 100ft?expand_more

8 AWG carrying 60A over 100ft has a 9.34V drop (7.78% on 120V), but 8 AWG is NEC-capped at 50A branch-circuit OCP per NEC 240.4(D), so 60A on 8 AWG is ampacity-invalid and the drop figure above is a reference calculation only, not an install spec. Reference: 3.89% on 240V.

Does wire material affect voltage drop?expand_more

Yes. Aluminum has roughly 1.3 to 1.4 times the resistance of copper at the NEC Chapter 9 Table 8 75°C reference temperature, so for the same voltage drop an aluminum conductor is typically one to two gauges larger than copper. The exact gap depends on whether ampacity or voltage drop is binding, and the install still needs anti-oxidant compound and aluminum-rated lugs.

What happens if voltage drop is too high?expand_more

Motors run hotter and can have trouble starting under load. Incandescent and halogen lighting dims. Some electronics misbehave at the low end of their input tolerance. Energy is wasted as I²R heating in the conductor. These are performance issues; high drop is not itself a code violation unless the specific installation cites a hard limit.

What wire gauge should I use instead of 8 AWG for this run?expand_more

This run is at 7.78% on 120V, past the 3% branch-circuit drop target. If you want to land under 3% at 60A over 100ft on 120V, the smallest gauge in our table that clears it is 3 AWG at 2.45%. Going up one size from 8 AWG is not always enough, each AWG step only drops the resistance by roughly 20-25%, so on long runs or high currents you often have to skip one or two sizes to meet the target. NEC 210.19(A) Informational Note 4 frames 3% as a recommendation, not a code requirement, so the right answer for you also depends on the load (motor startup, sensitive electronics) and how much drop is tolerable.

Is voltage drop worse on 120V or 240V?expand_more

Same wire, same amps, same distance: the volts dropped are identical. But the percentage is worse on 120V because the drop is a larger fraction of the source voltage. This run would be 3.89% on 240V versus 7.78% on 120V.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.