How Many Amps Is 1,840 Watts at 100V?
At 100V, 1,840 watts converts to 18.4 amps using the AC single-phase formula (Amps = Watts ÷ (V × PF)) at PF 1.0 for a resistive load. AC resistive at PF 1.0 and the DC baseline land on the same number at this voltage.
At 18.4A, the NEC 210.19(A) continuous-load sizing math (125% of the load, equivalently 80% of the breaker rating) points to a 25A breaker as the smallest standard size that covers this load continuously. A 20A breaker is the smallest standard size the raw current fits under, but it is non-continuous-only at this load.
Use this citation when referencing this page.
Assumes an AC single-phase resistive load at PF 1.0. Typing a commercial L-L voltage (208/400/480V) re-routes the result to three-phase; 277V stays on single-phase because it's the L-N lighting leg of a 480Y/277V wye; 12/24V re-routes to DC.
Formulas
DC: Watts to Amps
I(A) = P(W) ÷ V(V)
AC Single Phase (PF = 0.85)
I(A) = P(W) ÷ (PF × V(V))
Circuit Sizing
Breaker Sizing
NEC 240.6(A) standard ampere ratings for branch-circuit and feeder breakers start at 15, 20, 25, 30, 35, 40, 45, and 50A and continue at 60A and above for feeder and large-appliance circuits. At 18.4A, the smallest standard breaker the raw current fits under is 20A, but that breaker only covers 20A non-continuously; NEC 210.19(A) requires conductor and OCP sized at 125% of any continuous load (equivalently 80% of breaker rating), so for a continuous load the smallest compliant breaker is 25A. Final selection still depends on the equipment nameplate, whether the load is continuous, conductor ampacity, and local code.
| Breaker Size | Max Continuous Load (80%) | Status for 18.4A |
|---|---|---|
| 15A | 12A | Too small |
| 20A | 16A | Non-continuous only |
| 25A | 20A | OK for continuous |
| 30A | 24A | OK for continuous |
| 35A | 28A | OK for continuous |
| 40A | 32A | OK for continuous |
| 45A | 36A | OK for continuous |
| 50A | 40A | OK for continuous |
Energy Cost
Running 1,840W costs approximately $0.31 per hour at the US average rate of $0.17/kWh (rates last reviewed April 2026). That is $2.50 for 8 hours or about $75.07 per month. See detailed cost breakdown.
AC Conversion Detail
The DC baseline for 1,840W at 100V is 18.4A. On an AC circuit with a power factor of 0.85, the current rises to 21.65A because reactive current flows alongside the real-power current.
| Circuit Type | Formula | Result |
|---|---|---|
| DC | 1,840 ÷ 100 | 18.4 A |
| AC Single Phase (PF 0.85) | 1,840 ÷ (100 × 0.85) | 21.65 A |
Power Factor Reference
Power factor is the main reason 1,840W draws more current on AC than DC. At PF 1.0 (pure resistive, like a heater), the load pulls 18.4A at 100V on the single-phase basis the rest of the page uses. At PF 0.80 (typical induction motor), the same 1,840W pulls 23A. That is an extra 4.6A just to overcome the reactive component. Use the typical values below as a starting point, not for precise engineering calculations.
| Load Type | Typical PF | 1,840W at 100V (single-phase) |
|---|---|---|
| Resistive (heaters, incandescent) | 1 | 18.4 A |
| Fluorescent lamps | 0.95 | 19.37 A |
| LED lighting | 0.9 | 20.44 A |
| Synchronous motors | 0.9 | 20.44 A |
| Typical mixed loads | 0.85 | 21.65 A |
| Induction motors (full load) | 0.8 | 23 A |
| Computers (without PFC) | 0.65 | 28.31 A |
| Induction motors (no load) | 0.35 | 52.57 A |
Same Wattage, Other Voltages
Related Calculations
Other Wattages at 100V
| Watts | AC 1Φ Amps PF 1.0 resistive | AC 1Φ Amps PF 0.85 motor |
|---|---|---|
| 700W | 7A | 8.24A |
| 750W | 7.5A | 8.82A |
| 800W | 8A | 9.41A |
| 900W | 9A | 10.59A |
| 1,000W | 10A | 11.76A |
| 1,100W | 11A | 12.94A |
| 1,200W | 12A | 14.12A |
| 1,300W | 13A | 15.29A |
| 1,400W | 14A | 16.47A |
| 1,500W | 15A | 17.65A |
| 1,600W | 16A | 18.82A |
| 1,700W | 17A | 20A |
| 1,800W | 18A | 21.18A |
| 1,900W | 19A | 22.35A |
| 2,000W | 20A | 23.53A |
| 2,200W | 22A | 25.88A |
| 2,400W | 24A | 28.24A |
| 2,500W | 25A | 29.41A |
| 2,700W | 27A | 31.76A |
| 3,000W | 30A | 35.29A |