swap_horiz Looking to convert 28.35A at 120V back to watts?

How Many Amps Is 3,402 Watts at 120V?

3,402 watts equals 28.35 amps at 120V on an AC single-phase resistive circuit (PF 1.0). AC resistive at PF 1.0 and the DC baseline land on the same number at this voltage.

At 28.35A, the NEC 210.19(A) continuous-load sizing math (125% of the load, equivalently 80% of the breaker rating) points to a 40A breaker as the smallest standard size that covers this load continuously. A 30A breaker is the smallest standard size the raw current fits under, but it is non-continuous-only at this load.

3,402 watts at 120V

28.35 Amps

3,402 watts equals 28.35 amps at 120 volts (AC single-phase, PF 1.0 resistive)

DC28.35 A

Try: 3,500W at 120V 3,000W at 120V 4,000W at 120V 2,700W at 120V

Watts

Volts

Amps (AC 1Φ, PF 1.0)

28.35

Assumes an AC single-phase resistive load at PF 1.0. Typing a commercial L-L voltage (208/400/480V) re-routes the result to three-phase; 277V stays on single-phase because it's the L-N lighting leg of a 480Y/277V wye; 12/24V re-routes to DC.

Formulas

DC: Watts to Amps

I_(A) = P_(W) ÷ V_(V)

3,402 ÷ 120 = 28.35 A

AC Single Phase (PF = 0.85)

I_(A) = P_(W) ÷ (PF × V_(V))

3,402 ÷ (0.85 × 120) = 3,402 ÷ 102 = 33.35 A

Circuit Sizing

Breaker Sizing

NEC 240.6(A) standard ampere ratings for branch-circuit and feeder breakers start at 15, 20, 25, 30, 35, 40, 45, and 50A and continue at 60A and above for feeder and large-appliance circuits. At 28.35A, the smallest standard breaker the raw current fits under is 30A, but that breaker only covers 30A non-continuously; NEC 210.19(A) requires conductor and OCP sized at 125% of any continuous load (equivalently 80% of breaker rating), so for a continuous load the smallest compliant breaker is 40A. Final selection still depends on the equipment nameplate, whether the load is continuous, conductor ampacity, and local code.

Breaker Size	Max Continuous Load (80%)	Status for 28.35A
15A	12A	Too small
20A	16A	Too small
25A	20A	Too small
30A	24A	Non-continuous only
35A	28A	Non-continuous only
40A	32A	OK for continuous
45A	36A	OK for continuous
50A	40A	OK for continuous

Energy Cost

Running 3,402W costs approximately $0.58 per hour at the US average rate of $0.17/kWh (rates last reviewed April 2026). That is $4.63 for 8 hours or about $138.80 per month. See detailed cost breakdown.

AC Conversion Detail

The DC baseline for 3,402W at 120V is 28.35A. On an AC circuit with a power factor of 0.85, the current rises to 33.35A because reactive current flows alongside the real-power current.

Circuit Type	Formula	Result
DC	3,402 ÷ 120	28.35 A
AC Single Phase (PF 0.85)	3,402 ÷ (120 × 0.85)	33.35 A

Power Factor Reference

Power factor is the main reason 3,402W draws more current on AC than DC. At PF 1.0 (pure resistive, like a heater), the load pulls 28.35A at 120V on the single-phase basis the rest of the page uses. At PF 0.80 (typical induction motor), the same 3,402W pulls 35.44A. That is an extra 7.09A just to overcome the reactive component. Use the typical values below as a starting point, not for precise engineering calculations.

Load Type	Typical PF	3,402W at 120V (single-phase)
Resistive (heaters, incandescent)	1	28.35 A
Fluorescent lamps	0.95	29.84 A
LED lighting	0.9	31.5 A
Synchronous motors	0.9	31.5 A
Typical mixed loads	0.85	33.35 A
Induction motors (full load)	0.8	35.44 A
Computers (without PFC)	0.65	43.62 A
Induction motors (no load)	0.35	81 A

Same Wattage, Other Voltages

bolt3,402W at 12V = 283.5ADC bolt3,402W at 24V = 141.75ADC bolt3,402W at 100V = 34.02A1Φ, PF 1.0 bolt3,402W at 208V = 11.11A3Φ per line, PF 0.85 bolt3,402W at 220V = 15.46A1Φ, PF 1.0 bolt3,402W at 230V = 14.79A1Φ, PF 1.0 bolt3,402W at 240V = 14.18A1Φ, PF 1.0 bolt3,402W at 277V = 12.28A1Φ, PF 1.0 bolt3,402W at 400V = 5.78A3Φ per line, PF 0.85 bolt3,402W at 460V = 5.02A3Φ per line, PF 0.85 bolt3,402W at 480V = 4.81A3Φ per line, PF 0.85 bolt3,402W at 575V = 4.02A3Φ per line, PF 0.85

swap_horiz 28.4A to watts at 120V payments 3,402W running cost cable Wire size for 28.35A at 120V electrical_services 3.4 kW to amps science Ohm's law: 120V & 28A functions Watts to amps formula

Other Wattages at 120V

Watts	AC 1Φ Amps PF 1.0 resistive	AC 1Φ Amps PF 0.85 motor
1,000W	8.33A	9.8A
1,100W	9.17A	10.78A
1,200W	10A	11.76A
1,300W	10.83A	12.75A
1,400W	11.67A	13.73A
1,500W	12.5A	14.71A
1,600W	13.33A	15.69A
1,700W	14.17A	16.67A
1,800W	15A	17.65A
1,900W	15.83A	18.63A
2,000W	16.67A	19.61A
2,200W	18.33A	21.57A
2,400W	20A	23.53A
2,500W	20.83A	24.51A
2,700W	22.5A	26.47A
3,000W	25A	29.41A
3,500W	29.17A	34.31A
4,000W	33.33A	39.22A
4,500W	37.5A	44.12A
5,000W	41.67A	49.02A

Frequently Asked Questions

How many amps is 3,402W at 120V? expand_more

3,402W at 120V draws 28.35 amps on AC single-phase at PF 1.0 (resistive). For comparison at the same voltage: 28.35A on DC, 33.35A on AC single-phase at PF 0.85. Actual current depends on the load's power factor.

Can I plug a 3,402W appliance into a standard 120V outlet? expand_more

No. 3,402W on 120V draws more than a 20A circuit can sustain. A dedicated 240V circuit is the practical option.

Does voltage affect how many amps 3,402W draws? expand_more

Yes. Higher voltage means lower current for the same real power. 3,402W at 120V draws 28.35A on AC single-phase at PF 1.0 (resistive). As a resistive-baseline comparison at the same wattage, a DC or PF 1.0 load would draw 56.7A at 60V and 14.18A at 240V. Doubling the voltage halves the current and also halves the I²R losses in the conductors.

What is the 80% continuous load rule for 3,402W? expand_more

NEC 210.19(A) sizes the conductor and overcurrent device at not less than 125% of any continuous load (a load that runs three hours or more), equivalently 80% of the breaker rating. At 28.35A (the current the branch conductors actually carry on AC single-phase at PF 1.0 (resistive)), the minimum breaker that satisfies this is 40A under typical assumptions. Brief non-continuous use can run closer to the full breaker rating, but space heaters, EV chargers, and long-running appliances should be sized for the continuous case.

Should I run 3,402W on a 15A circuit or a 20A circuit? expand_more

At 28.35A the load sits past the 80% continuous-load figure of a 120V/20A circuit (1,920W). A dedicated 240V circuit is the practical option for sustained operation.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.