How Many Amps Is 420 Watts at 24V?
420 watts equals 17.5 amps at 24V on a DC circuit. On AC single-phase at PF 0.85 the same real power would be 20.59 amps.
At 17.5A, the NEC 210.19(A) continuous-load sizing math (125% of the load, equivalently 80% of the breaker rating) points to a 25A breaker as the smallest standard size that covers this load continuously. A 20A breaker is the smallest standard size the raw current fits under, but it is non-continuous-only at this load.
Use this citation when referencing this page.
Assumes a DC circuit. Typing a commercial L-L voltage (208/400/480V) re-routes the result to three-phase; 277V stays on single-phase because it's the L-N lighting leg of a 480Y/277V wye; 12/24V re-routes to DC.
Formulas
DC: Watts to Amps
I(A) = P(W) ÷ V(V)
AC Single Phase (PF = 0.85)
I(A) = P(W) ÷ (PF × V(V))
Circuit Sizing
Breaker Sizing
NEC 240.6(A) standard ampere ratings for branch-circuit and feeder breakers start at 15, 20, 25, 30, 35, 40, 45, and 50A and continue at 60A and above for feeder and large-appliance circuits. At 17.5A, the smallest standard breaker the raw current fits under is 20A, but that breaker only covers 20A non-continuously; NEC 210.19(A) requires conductor and OCP sized at 125% of any continuous load (equivalently 80% of breaker rating), so for a continuous load the smallest compliant breaker is 25A. Final selection still depends on the equipment nameplate, whether the load is continuous, conductor ampacity, and local code.
| Breaker Size | Max Continuous Load (80%) | Status for 17.5A |
|---|---|---|
| 15A | 12A | Too small |
| 20A | 16A | Non-continuous only |
| 25A | 20A | OK for continuous |
| 30A | 24A | OK for continuous |
| 35A | 28A | OK for continuous |
| 40A | 32A | OK for continuous |
| 45A | 36A | OK for continuous |
| 50A | 40A | OK for continuous |
Energy Cost
Running 420W costs approximately $0.07 per hour at the US average rate of $0.17/kWh (rates last reviewed April 2026). That is $0.57 for 8 hours or about $17.14 per month. See detailed cost breakdown.
AC Conversion Detail
The DC baseline for 420W at 24V is 17.5A. On an AC circuit with a power factor of 0.85, the current rises to 20.59A because reactive current flows alongside the real-power current.
| Circuit Type | Formula | Result |
|---|---|---|
| DC | 420 ÷ 24 | 17.5 A |
| AC Single Phase (PF 0.85) | 420 ÷ (24 × 0.85) | 20.59 A |
Power Factor Reference
Power factor is the main reason 420W draws more current on AC than DC. At PF 1.0 (pure resistive, like a heater), the load pulls 17.5A at 24V on the single-phase basis the rest of the page uses. At PF 0.80 (typical induction motor), the same 420W pulls 21.87A. That is an extra 4.37A just to overcome the reactive component. Use the typical values below as a starting point, not for precise engineering calculations.
| Load Type | Typical PF | 420W at 24V (single-phase) |
|---|---|---|
| Resistive (heaters, incandescent) | 1 | 17.5 A |
| Fluorescent lamps | 0.95 | 18.42 A |
| LED lighting | 0.9 | 19.44 A |
| Synchronous motors | 0.9 | 19.44 A |
| Typical mixed loads | 0.85 | 20.59 A |
| Induction motors (full load) | 0.8 | 21.87 A |
| Computers (without PFC) | 0.65 | 26.92 A |
| Induction motors (no load) | 0.35 | 50 A |
Same Wattage, Other Voltages
Related Calculations
Other Wattages at 24V
| Watts | DC Amps | AC 1Φ Amps PF 0.85 |
|---|---|---|
| 25W | 1.04A | 1.23A |
| 30W | 1.25A | 1.47A |
| 40W | 1.67A | 1.96A |
| 50W | 2.08A | 2.45A |
| 60W | 2.5A | 2.94A |
| 75W | 3.13A | 3.68A |
| 100W | 4.17A | 4.9A |
| 120W | 5A | 5.88A |
| 150W | 6.25A | 7.35A |
| 200W | 8.33A | 9.8A |
| 250W | 10.42A | 12.25A |
| 300W | 12.5A | 14.71A |
| 350W | 14.58A | 17.16A |
| 400W | 16.67A | 19.61A |
| 450W | 18.75A | 22.06A |
| 500W | 20.83A | 24.51A |
| 600W | 25A | 29.41A |
| 700W | 29.17A | 34.31A |
| 750W | 31.25A | 36.76A |
| 800W | 33.33A | 39.22A |