What Wire Size for 24.49 Amps at 250 Feet?

For a 24.49-amp circuit running 250 feet on 120V, 3 AWG copper is the smallest gauge in our table that both stays within the 3% drop target and covers the branch-circuit OCP cap for 24.49A. A shorter run of 125 feet at the same voltage often allows 6 AWG. Treat this as an estimate, not an install spec.

24.49A at 250ft · 120V single-phase / DC · 3% drop target

3 AWG copper

On a 240V circuit (copper)6 AWG

Voltage drop (120V, copper)3V (2.5%)

No aluminum row: every aluminum size in our reference table sits past the 3% drop target at 250 feet on 120V, or the amperage is below the 30A residential threshold where aluminum is not a typical pick. On a higher source voltage, a shorter run, or a looser drop target, aluminum is still the standard feeder material at higher amperages.

check_circle Within the 3% branch and 5% feeder+branch total drop targets

Amps

Feet

Gauge (Cu / Al)

3 AWG Cu

Assumes a 120V source on a single-phase / DC circuit and a 3% voltage-drop target. Each material is picked independently against the same target, so the copper and aluminum results are two separate recommendations, not an ampacity equivalence. Switch to three-phase L-L →

How Wire Size Is Determined

Step 1: NEC Branch-Circuit Ampacity

3 AWG branch-circuit OCP (100A) ≥ 24.49A ✓

The conductor needs to carry at least 24.49A without going past its temperature rating, and the OCP protecting it needs to respect the NEC branch-circuit cap. Under the typical assumptions used in this table (copper, 75°C termination, no bundling or ambient derates), 3 AWG sits at a branch-circuit OCP of 100A. That is not a universal number: NM-B cable (Romex) follows the 60°C column in residential use per NEC 334.80 (3 AWG NM-B = 85A), bundling more than three current-carrying conductors requires a 310.15(C)(1) adjustment, ambient temperatures above 30°C require a 310.15(B) correction, and 60°C terminations on typical residential equipment can pull the usable value lower still. Use the nameplate and local code for the actual install value.

Step 2: Voltage Drop Check

%VD = (2 × L × I × R) ÷ (1000 × V) × 100 (single-phase / DC; round-trip factor of 2)

(2 × 250 × 24.49 × 0.245) ÷ (1000 × 120) × 100 = 2.5%

NEC 210.19(A) Informational Note 4 recommends ≤ 3% for branch circuits and ≤ 5% for feeder + branch total as performance targets, not hard code requirements. This run sits within the 3% target used for this calculation.

Practical Information

What If You Go One Size Smaller?

Using 4 AWG (one size thinner) at these inputs gives a voltage drop of 3.77V (3.14% on 120V), and its branch-circuit OCP cap under typical conditions is 85A.

Limiting factor here: voltage drop, not ampacity. 4 AWG is still above the 24.49A load at its 85A branch-circuit OCP cap, so the conductor temperature margin is fine for this run. What pushes it off this page's pick is the 3.14% drop sitting past the 3% target, which is a performance recommendation (NEC 210.19(A) Informational Note 4), not a code requirement. On shorter runs or at higher source voltage the same gauge would often clear the drop target too.

What If You Go One Size Larger?

Using 2 AWG (one size thicker) would reduce voltage drop to 2.38V (1.98% on 120V). More expensive wire but better performance and more headroom for future load increases.

Wattage at This Amperage

24.49A at 120V delivers 2,938.8 watts (DC / resistive load). See conversion.

Related Calculations

trending_down V-drop: 3 AWG, 24.49A, 250ft electric_bolt 24.49A to watts at 120V functions Wire sizing formula

Frequently Asked Questions

What wire size for 24.49 amps at 250 feet on 120V?expand_more

24.49A at 250ft on 120V is commonly served by 3 AWG copper to land under the 3% voltage-drop target, under the typical 75°C-termination assumptions used in this table. Actual install sizing also depends on conductor material, insulation and termination temperature rating, cable type, ambient and bundling conditions, and local code.

Can I run 24.49A on a longer distance?expand_more

Yes, but you may need thicker wire. At 500ft on 120V, check the wire size calculator. You may need to go up one or two gauges.

Do I need to upsize wire for continuous loads?expand_more

NEC 210.19(A) (branch circuits) and 215.3 (feeders) size the conductor and overcurrent device at not less than 125% of the continuous load plus 100% of any non-continuous load. For a 24.49A continuous load that points the sizing math at the 30.61A figure, but the actual conductor and breaker pick still depends on termination temperature rating, cable type, bundling and ambient conditions, and any 240.4(D) or 240.4(B) provisions. Treat this as the input to a sizing decision, not the output.

What is the NEC voltage drop recommendation?expand_more

NEC 210.19(A) Informational Note 4 recommends ≤3% for branch circuits and ≤5% total (feeder + branch). These are performance recommendations, not hard code requirements.

Copper or aluminum wire for 24.49A?expand_more

Copper and aluminum are picked independently against the same drop target on this site; neither pick implies ampacity equivalence with the other. At 24.49A residential branch-circuit territory, copper is the default. Aluminum in 14/12/10 AWG is not typical for residential branches, both for code reasons (the NEC 240.4(D) small-conductor rule caps aluminum branch OCP tighter than copper) and because termination and anti-oxidation requirements add cost at that scale.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.