How Many Amps Does a 1.5 HP single-phase Motor Draw at 230V?

Q: What is 1.5 HP in watts?

1.5 HP equals 1,119 watts of mechanical output (1 HP = 746 W). The electrical input at the terminals is higher because no motor is 100% efficient: at 85% efficiency the input is about 1,316.47 W.

1.5 HP single-phase motor at 230V draws 6.73 amps. Single-phase motors are the standard for residential applications and small equipment. The amp draw depends on voltage, motor efficiency, and power factor.

Typical 1.5 HP motor applications: air compressors, well pumps, woodworking tools, small shop equipment.

1.5 HP single-phase motor at 230V

6.73 Amps running

Calculated running current at the motor terminals at the assumed 85% efficiency and PF 0.85. This is a conversion from the nameplate horsepower using those assumptions, not a measured value; a real meter reading depends on the motor's actual nameplate efficiency, loading, temperature, and motor design.

NEC Table 430.248 FLC (code sizing base)10 A

Conductor min ampacity (NEC 430.22, 125% of FLC)12.5 A

Electrical input (HP × 746 ÷ efficiency)1,316.47 W

Try: 1HP at 230V 2HP at 230V 3/4HP at 230V 1/2HP at 230V

Volts

Motor Type

Running Amps (meter)

6.73

NEC Table 430.248 FLC (code sizing)

Use the running amps for metering and energy calculations. For branch-circuit sizing, AC motors use the NEC Table 430.248 / 430.250 full-load current under NEC 430.6(A)(1); DC motors use the motor nameplate full-load current under NEC 430.6(A)(3), with Table 430.247 as the reference. Three-phase current is shown per line on a balanced circuit.

Formula (single-phase)

I_(A) = (HP × 746) ÷ (V × Eff × PF)

(1.5 × 746) ÷ (230 × 0.85 × 0.85) = 1,119 ÷ 166.17 = 6.73 A

Convert HP to watts: 1.5 × 746 = 1,119W
Denominator: 230 × 0.85 × 0.85 = 166.17
Result: 1,119 ÷ 166.17 = 6.73 amps

NEC Reference Values

This section lists the Code reference numbers a motor branch circuit is sized from. Final conductor, breaker, disconnect, and overload selection is an install decision a licensed electrician makes against the motor nameplate, the actual install conditions, and the applicable NEC articles, not a decision a conversion page can make for you.

NEC Sizing Base: NEC Table 430.248 FLC

Per NEC 430.6(A)(1), motor branch-circuit conductors, switches, and overcurrent protection are sized from the values in Table 430.248 (single-phase) or Table 430.250 (three-phase), not from the motor nameplate and not from a calculated full-load amps. For a 1.5 HP single-phase motor at 230V, the table value is 10 A (the 115V column covers 110-120V systems under 430.6(A)(1)).

The 6.73 A shown in the hero is the calculated running current at 85% efficiency and PF 0.85. This is a conversion from the nameplate horsepower under those assumptions, not a measured value; a real meter reading depends on the motor's actual efficiency, loading, temperature, and design. Use this figure for energy and metering estimates, and use 10 A as the reference FLC when an electrician walks through NEC 430 against the nameplate.

NEC 430.22 Conductor Rule (reference formula)

NEC 430.22 requires motor branch-circuit conductor ampacity of at least 125% of the Code sizing FLC. As a reference calculation against the NEC Table 430.248 value: 10 × 1.25 = 12.5 A. The selected conductor is taken from NEC Table 310.16 at the applicable termination temperature column, with ambient, bundling, and cable-type adjustments applied by the installer. Motor branch-circuit conductors are exempt from the 240.4(D) small-conductor rule via 240.4(G).

NEC 430.52 Overcurrent Protection (code caps)

NEC Table 430.52(C)(1) gives the maximum rating for motor short-circuit and ground-fault protection as a percentage of the Code sizing FLC. The percentage depends on the device type:

Device Type	Maximum % of Table FLC (430.52(C)(1))
Non-time-delay fuse	300%
Dual-element (time-delay) fuse	175%
Inverse-time circuit breaker	250%
Instantaneous-trip circuit breaker	800%

These percentages are maximum caps, not install picks. A real circuit applies the percentage against the Code sizing FLC for the specific device type, rounds up to a standard size per 430.52(C)(1)(a), and is verified against the motor nameplate and the install conditions by the installer. The elevated percentages exist so short-circuit protection does not nuisance-trip on locked-rotor startup inrush.

Locked Rotor (Startup) Current

During the first 2-5 seconds of startup, a squirrel-cage induction motor typically draws 5 to 7 times the NEC Table 430.248 FLC of 10 A (roughly 50 to 70 A). This is why the 430.52(C)(1) percentages above are so much higher than running current: the short-circuit/ground-fault protective device has to ride through locked-rotor inrush without tripping. Actual LRA is set by the motor's NEMA code letter on the nameplate and should be checked there for a real install.

Current	Amps	Duration
Calculated running current (meter)	6.73 A	Continuous at full load
NEC Table 430.248 FLC (Code reference)	10 A	Sizing base, not metered
Locked rotor (typical, 5-7×)	50-70 A	2-5 seconds

Operating Cost

Motor mechanical output is 1,119 W (1.5 HP × 746). Electrical input at the terminals is higher because no motor is 100% efficient: 1,119 ÷ 0.85 = 1,316.47 W. At $0.17/kWh, running cost is $0.22/hour or $53.71/month at 8 hours/day. Full breakdown at 1,316.47 W.

Amps by Motor Efficiency (single-phase)

Motor efficiency directly affects amp draw. A more efficient motor draws less current for the same HP output. Values below are the calculated single-phase running current at 230V and PF 0.85:

Efficiency	Amps at 230V	Watts Consumed	Waste Heat
75%	7.63 A	1,492 W	373 W
80%	7.15 A	1,398.75 W	279.75 W
85%	6.73 A	1,316.47 W	197.47 W
90%	6.36 A	1,243.33 W	124.33 W
95%	6.03 A	1,177.89 W	58.89 W

Other HP Values at 230V (single-phase)

Running current is the calculated single-phase draw at 85% efficiency and 0.85 PF (a conversion from HP under those assumptions, not a measured value). NEC Table FLC is the value from NEC Table 430.248 used for branch-circuit conductor and OCP sizing under NEC 430.6(A)(1). LRA is estimated at 5-7× the NEC table FLC; rows outside the table show n/a because there is no code-authoritative LRA basis for that HP/voltage/phase combination. Row links open each result page in single-phase mode.

HP	Running Amps (calculated)	NEC Table 430.248 FLC	LRA Estimate (5-7× FLC)
1/8 HP	0.5612 A	off-table	n/a
1/6 HP	0.7484 A	2.2 A	11-15.4 A
1/4 HP	1.12 A	2.9 A	14.5-20.3 A
1/3 HP	1.5 A	3.6 A	18-25.2 A
1/2 HP	2.24 A	4.9 A	24.5-34.3 A
3/4 HP	3.37 A	6.9 A	34.5-48.3 A
1 HP	4.49 A	8 A	40-56 A
1.5 HP	6.73 A	10 A	50-70 A
2 HP	8.98 A	12 A	60-84 A
3 HP	13.47 A	17 A	85-119 A
5 HP	22.45 A	28 A	140-196 A
7.5 HP	33.67 A	40 A	200-280 A
10 HP	44.89 A	50 A	250-350 A
15 HP	67.34 A	off-table	n/a
20 HP	89.78 A	off-table	n/a
25 HP	112.23 A	off-table	n/a
30 HP	134.68 A	off-table	n/a
40 HP	179.57 A	off-table	n/a
50 HP	224.46 A	off-table	n/a
75 HP	336.69 A	off-table	n/a

Same HP, Other Voltages (single-phase)

speed 1.5 HP at 120V = 12.91A speed 1.5 HP at 208V = 7.45A speed 1.5 HP at 220V = 7.04A speed 1.5 HP at 240V = 6.45A speed 1.5 HP at 400V = 3.87A speed 1.5 HP at 480V = 3.23A

Related Calculations

bolt 1,316W electrical input to amps at 230V payments 1,316W running cost cable Wire size for 12.5A at 230V (NEC 430.22 minimum: 125% of 10A NEC Table 430.248 FLC)

Frequently Asked Questions

How many amps does a 1.5 HP single-phase motor draw at 230V?expand_more

At the terminals, a 1.5 HP single-phase motor at 230V draws about 6.73 amps at 85% efficiency and 0.85 power factor. For NEC branch-circuit sizing use the NEC Table 430.248 full-load current instead: 10 A.

What is 1.5 HP in watts?expand_more

1.5 HP equals 1,119 watts of mechanical output (1 HP = 746 W). The electrical input at the terminals is higher because no motor is 100% efficient: at 85% efficiency the input is about 1,316.47 W.

What branch-circuit context does a 1.5 HP single-phase motor at 230V typically sit in?expand_more

At 230V single-phase, motor branches are dedicated circuits, not general-purpose receptacles. Common NEMA configurations at this voltage are the 6-series (6-15, 6-20, 6-30, 6-50) and the 14-series (14-30, 14-50) when a neutral is needed, sized to the motor branch-circuit OCP the installer picks under NEC 430.52(C)(1). The NEC Table 430.248 FLC of 10 A is the reference number an electrician feeds into 430.22 and 430.52, not a receptacle pick on its own. Verify against the nameplate and local code.

How does NEC 430.22 size conductors for a 1.5 HP single-phase motor?expand_more

NEC 430.22 requires motor branch-circuit conductors to have an ampacity of at least 125% of the NEC Table 430.248 FLC (not the motor nameplate, and not the calculated running current). As a reference formula against the table value: 10 A × 1.25. The specific conductor is picked from NEC Table 310.16 at the applicable termination temperature column, with ambient and bundling adjustments applied by the installer. Motor branches are exempt from the 240.4(D) small-conductor rule via 240.4(G).

Does motor efficiency affect amp draw?expand_more

Yes. A 1.5 HP single-phase motor at 90% efficiency draws 6.36 A at the terminals versus 7.63 A at 75% efficiency. Higher efficiency means lower running amps and lower electrical input wattage for the same mechanical output.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.