How Many Amps Is 375.13 kW at 400V?

375.13 kilowatts at 400V works out to roughly 637 amps on AC three-phase at PF 0.85. That is typical for commercial HVAC, industrial motors, rooftop units, and three-phase panel loads. See the DC and alternate-phase numbers below for other circuit types.

375.13 kW at 400V, AC three-phase (PF 0.85)
637 Amps
375.13 kilowatts at 400V on AC three-phase ≈ 637 amps
AC Single Phase (PF 0.85)1,103.32 A
DC (ideal baseline)937.82 A
637

Formulas

DC: kW to Amps

I(A) = 1000 × P(kW) ÷ V(V)

1000 × 375.13 ÷ 400 = 375,128 ÷ 400 = 937.82 A

AC Single Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (PF × V(V))

375,128 ÷ (0.85 × 400) = 375,128 ÷ 340 = 1,103.32 A

AC Three Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (√3 × PF × VL-L), where VL-L is the line-to-line voltage

375,128 ÷ (1.732 × 0.85 × 400) = 375,128 ÷ 588.88 = 637 A

Equipment & Circuit Sizing

Energy Cost

375.13 kW costs $63.77/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC three-phase)

How the line current for 375.13 kW at 400V changes with load power factor, on the same AC three-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load TypePF375.13 kW at 400V (AC three-phase)
Resistive (heaters, incandescent)1541.45 A
Fluorescent lamps0.95569.95 A
LED lighting0.9601.61 A
Synchronous motors0.9601.61 A
Typical mixed loads0.85637 A
Induction motors (full load)0.8676.81 A
Computers (without PFC)0.65833 A
Induction motors (no load)0.351,547 A

AC Conversion Comparison

On DC, 375.13kW at 400V draws 937.82A. AC single-phase at PF 0.85 pulls 1,103.32A because reactive current is added on top of the real power. Three-phase at the same voltage needs only 637A per line since the same 375.13kW is shared across three conductors instead of one.

Circuit TypeFormulaResult
DC375,128 ÷ 400937.82 A
AC Single Phase (PF 0.85)375,128 ÷ (0.85 × 400)1,103.32 A
AC Three Phase (PF 0.85)375,128 ÷ (1.732 × 0.85 × 400)637 A

Other kW Values at 400V

kWAC 3-Phase per line, PF 0.85AC 1-Phase PF 0.85
15 kW25.47 A44.12 A
18 kW30.57 A52.94 A
20 kW33.96 A58.82 A
22 kW37.36 A64.71 A
25 kW42.45 A73.53 A
30 kW50.94 A88.24 A
35 kW59.43 A102.94 A
40 kW67.92 A117.65 A
50 kW84.9 A147.06 A
60 kW101.89 A176.47 A
75 kW127.36 A220.59 A
100 kW169.81 A294.12 A
125 kW212.26 A367.65 A
150 kW254.71 A441.18 A
200 kW339.62 A588.24 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

Frequently Asked Questions

375.13 kW at 400V draws about 637 amps on an AC three-phase circuit at PF 0.85. Alternate cases at the same voltage: 937.82A on DC, 1,103.32A on AC single-phase.
375.13 kW is typically three-phase in commercial and industrial settings.
375.13 kW equals 375,128 watts. Multiply kilowatts by 1000.
Three-phase at 400V draws 637A per line versus 1,103.32A single-phase. Less current per conductor means smaller wire and lower I²R losses.
Industrial equipment operates at higher power levels. 375.13 kW is easier to express than 375,128W. The math is identical, just scaled by 1000.
This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.