How Many Amps Is 682 kW at 460V?

682 kilowatts at 460V works out to roughly 1,007.04 amps on AC three-phase at PF 0.85. That is typical for commercial HVAC, industrial motors, rooftop units, and three-phase panel loads. See the DC and alternate-phase numbers below for other circuit types.

682 kW at 460V, AC three-phase (PF 0.85)
1,007.04 Amps
682 kilowatts at 460V on AC three-phase ≈ 1,007.04 amps
AC Single Phase (PF 0.85)1,744.25 A
DC (ideal baseline)1,482.61 A
1,007.04

Formulas

DC: kW to Amps

I(A) = 1000 × P(kW) ÷ V(V)

1000 × 682 ÷ 460 = 682,000 ÷ 460 = 1,482.61 A

AC Single Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (PF × V(V))

682,000 ÷ (0.85 × 460) = 682,000 ÷ 391 = 1,744.25 A

AC Three Phase (PF = 0.85)

I(A) = 1000 × P(kW) ÷ (√3 × PF × VL-L), where VL-L is the line-to-line voltage

682,000 ÷ (1.732 × 0.85 × 460) = 682,000 ÷ 677.21 = 1,007.04 A

Equipment & Circuit Sizing

Energy Cost

682 kW costs $115.94/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC three-phase)

How the line current for 682 kW at 460V changes with load power factor, on the same AC three-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load TypePF682 kW at 460V (AC three-phase)
Resistive (heaters, incandescent)1855.98 A
Fluorescent lamps0.95901.04 A
LED lighting0.9951.09 A
Synchronous motors0.9951.09 A
Typical mixed loads0.851,007.04 A
Induction motors (full load)0.81,069.98 A
Computers (without PFC)0.651,316.9 A
Induction motors (no load)0.352,445.67 A

AC Conversion Comparison

On DC, 682kW at 460V draws 1,482.61A. AC single-phase at PF 0.85 pulls 1,744.25A because reactive current is added on top of the real power. Three-phase at the same voltage needs only 1,007.04A per line since the same 682kW is shared across three conductors instead of one.

Circuit TypeFormulaResult
DC682,000 ÷ 4601,482.61 A
AC Single Phase (PF 0.85)682,000 ÷ (0.85 × 460)1,744.25 A
AC Three Phase (PF 0.85)682,000 ÷ (1.732 × 0.85 × 460)1,007.04 A

Other kW Values at 460V

kWAC 3-Phase per line, PF 0.85AC 1-Phase PF 0.85
15 kW22.15 A38.36 A
18 kW26.58 A46.04 A
20 kW29.53 A51.15 A
22 kW32.49 A56.27 A
25 kW36.91 A63.94 A
30 kW44.3 A76.73 A
35 kW51.68 A89.51 A
40 kW59.06 A102.3 A
50 kW73.83 A127.88 A
60 kW88.6 A153.45 A
75 kW110.74 A191.82 A
100 kW147.66 A255.75 A
125 kW184.57 A319.69 A
150 kW221.49 A383.63 A
200 kW295.32 A511.51 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

Frequently Asked Questions

682 kW at 460V draws about 1,007.04 amps on an AC three-phase circuit at PF 0.85. Alternate cases at the same voltage: 1,482.61A on DC, 1,744.25A on AC single-phase.
682 kW is typically three-phase in commercial and industrial settings.
DC: Amps = (kW × 1000) ÷ Volts. AC single-phase: Amps = (kW × 1000) ÷ (Volts × PF). AC three-phase: Amps = (kW × 1000) ÷ (VoltsL-L × √3 × PF).
Three-phase at 460V draws 1,007.04A per line versus 1,744.25A single-phase. Less current per conductor means smaller wire and lower I²R losses.
682 kW equals 682,000 watts. Multiply kilowatts by 1000.
This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.