How Many Amps Is 682 kW at 480V?

At 480V, 682 kW pulls approximately 965.08 amps on AC three-phase (PF 0.85). This is the case typical for commercial HVAC, industrial motors, rooftop units, and three-phase panel loads. Always verify against the equipment nameplate for actual install sizing.

682 kW at 480V, AC three-phase (PF 0.85)

965.08 Amps

682 kilowatts at 480V on AC three-phase ≈ 965.08 amps

AC Single Phase (PF 0.85)1,671.57 A

DC (ideal baseline)1,420.83 A

Try: 200kW at 480V 150kW at 480V 125kW at 480V 100kW at 480V

Volts

Amps (AC three-phase, PF 0.85)

965.08

Formulas

DC: kW to Amps

I_(A) = 1000 × P_(kW) ÷ V_(V)

1000 × 682 ÷ 480 = 682,000 ÷ 480 = 1,420.83 A

AC Single Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (PF × V_(V))

682,000 ÷ (0.85 × 480) = 682,000 ÷ 408 = 1,671.57 A

AC Three Phase (PF = 0.85)

I_(A) = 1000 × P_(kW) ÷ (√3 × PF × V_L-L), where V_L-L is the line-to-line voltage

682,000 ÷ (1.732 × 0.85 × 480) = 682,000 ÷ 706.66 = 965.08 A

Equipment & Circuit Sizing

Energy Cost

682 kW costs $115.94/hour at $0.17/kWh (rates last reviewed April 2026). See breakdown.

Power Factor Reference (AC three-phase)

How the line current for 682 kW at 480V changes with load power factor, on the same AC three-phase circuit basis the rest of the page uses. DC has no power factor; PF 1.0 represents resistive AC loads.

Load Type	PF	682 kW at 480V (AC three-phase)
Resistive (heaters, incandescent)	1	820.32 A
Fluorescent lamps	0.95	863.49 A
LED lighting	0.9	911.47 A
Synchronous motors	0.9	911.47 A
Typical mixed loads	0.85	965.08 A
Induction motors (full load)	0.8	1,025.4 A
Computers (without PFC)	0.65	1,262.03 A
Induction motors (no load)	0.35	2,343.77 A

AC Conversion Comparison

On DC, 682kW at 480V draws 1,420.83A. AC single-phase at PF 0.85 pulls 1,671.57A because reactive current is added on top of the real power. Three-phase at the same voltage needs only 965.08A per line since the same 682kW is shared across three conductors instead of one.

Circuit Type	Formula	Result
DC	682,000 ÷ 480	1,420.83 A
AC Single Phase (PF 0.85)	682,000 ÷ (0.85 × 480)	1,671.57 A
AC Three Phase (PF 0.85)	682,000 ÷ (1.732 × 0.85 × 480)	965.08 A

Other kW Values at 480V

kW	AC 3-Phase per line, PF 0.85	AC 1-Phase PF 0.85
15 kW	21.23 A	36.76 A
18 kW	25.47 A	44.12 A
20 kW	28.3 A	49.02 A
22 kW	31.13 A	53.92 A
25 kW	35.38 A	61.27 A
30 kW	42.45 A	73.53 A
35 kW	49.53 A	85.78 A
40 kW	56.6 A	98.04 A
50 kW	70.75 A	122.55 A
60 kW	84.9 A	147.06 A
75 kW	106.13 A	183.82 A
100 kW	141.51 A	245.1 A
125 kW	176.88 A	306.37 A
150 kW	212.26 A	367.65 A
200 kW	283.01 A	490.2 A

Same kW, Other Voltages

Each destination page leads with the interpretation most common for that voltage, so the amps shown below use the same basis as the page you'd land on: single-phase for residential voltages, three-phase for commercial/industrial panel voltages, DC for low-voltage.

electrical_services 682 kW at 400V = 1,158.1A (3-phase) electrical_services 682 kW at 460V = 1,007.04A (3-phase) electrical_services 682 kW at 575V = 805.63A (3-phase)

Related Calculations

bolt 682,000W to amps at 480V payments 682,000W running cost cable Wire size for 965.08A at 480V (3Φ)

Frequently Asked Questions

How many amps is 682 kW at 480V?expand_more

682 kW at 480V draws about 965.08 amps on an AC three-phase circuit at PF 0.85. Alternate cases at the same voltage: 1,420.83A on DC, 1,671.57A on AC single-phase.

How many amps does a 682 kW EV charger draw at 480V?expand_more

480V is commercial/industrial panel voltage, not a typical AC EVSE feed to a vehicle. On three-phase 480V, 682 kW works out to about 965.08A per line (three-phase at PF 0.85). In practice, 400-480V three-phase is usually the AC input to a DC fast charger (50-350 kW CCS/NACS stations like Tesla Superchargers), which rectifies to DC and delivers that directly to the vehicle, rather than an AC EVSE connector. A 682 kW figure at 480V is most likely the AC feed to a smaller commercial cabinet or the control-side input of a larger DC fast charger, not an at-the-car AC current.

How much does 682 kW cost to run?expand_more

682 kW costs $115.94 per hour at $0.17/kWh (US residential average, last reviewed April 2026). At 8 hours/day that is $27,825.60 per month.

Why do industrial systems use kW instead of watts?expand_more

Industrial equipment operates at higher power levels. 682 kW is easier to express than 682,000W. The math is identical, just scaled by 1000.

How does three-phase affect the amps for 682 kW?expand_more

Three-phase at 480V draws 965.08A per line versus 1,671.57A single-phase. Less current per conductor means smaller wire and lower I²R losses.

This calculator provides estimates for reference purposes only. Always consult a licensed electrician and verify compliance with the National Electrical Code (NEC) and local electrical codes before performing any electrical work.