How Many Amps Is 1,380 Watts at 24V?
1,380 watts equals 57.5 amps at 24V on a DC circuit. On AC single-phase at PF 0.85 the same real power would be 67.65 amps.
At 57.5A, the NEC 210.19(A) continuous-load sizing math (125% of the load, equivalently 80% of the breaker rating) points to a 80A breaker as the smallest standard size that covers this load continuously. A 60A breaker is the smallest standard size the raw current fits under, but it is non-continuous-only at this load.
Use this citation when referencing this page.
Assumes a DC circuit. Typing a commercial L-L voltage (208/400/480V) re-routes the result to three-phase; 277V stays on single-phase because it's the L-N lighting leg of a 480Y/277V wye; 12/24V re-routes to DC.
Formulas
DC: Watts to Amps
I(A) = P(W) ÷ V(V)
AC Single Phase (PF = 0.85)
I(A) = P(W) ÷ (PF × V(V))
Circuit Sizing
Breaker Sizing
NEC 240.6(A) standard ampere ratings for branch-circuit and feeder breakers start at 15, 20, 25, 30, 35, 40, 45, and 50A and continue at 60A and above for feeder and large-appliance circuits. At 57.5A, the smallest standard breaker the raw current fits under is 60A, but that breaker only covers 60A non-continuously; NEC 210.19(A) requires conductor and OCP sized at 125% of any continuous load (equivalently 80% of breaker rating), so for a continuous load the smallest compliant breaker is 80A. Final selection still depends on the equipment nameplate, whether the load is continuous, conductor ampacity, and local code.
| Breaker Size | Max Continuous Load (80%) | Status for 57.5A |
|---|---|---|
| 40A | 32A | Too small |
| 45A | 36A | Too small |
| 50A | 40A | Too small |
| 60A | 48A | Non-continuous only |
| 70A | 56A | Non-continuous only |
| 80A | 64A | OK for continuous |
| 90A | 72A | OK for continuous |
| 100A | 80A | OK for continuous |
| 110A | 88A | OK for continuous |
Energy Cost
Running 1,380W costs approximately $0.23 per hour at the US average rate of $0.17/kWh (rates last reviewed April 2026). That is $1.88 for 8 hours or about $56.30 per month. See detailed cost breakdown.
AC Conversion Detail
The DC baseline for 1,380W at 24V is 57.5A. On an AC circuit with a power factor of 0.85, the current rises to 67.65A because reactive current flows alongside the real-power current.
| Circuit Type | Formula | Result |
|---|---|---|
| DC | 1,380 ÷ 24 | 57.5 A |
| AC Single Phase (PF 0.85) | 1,380 ÷ (24 × 0.85) | 67.65 A |
Power Factor Reference
Power factor is the main reason 1,380W draws more current on AC than DC. At PF 1.0 (pure resistive, like a heater), the load pulls 57.5A at 24V on the single-phase basis the rest of the page uses. At PF 0.80 (typical induction motor), the same 1,380W pulls 71.87A. That is an extra 14.37A just to overcome the reactive component. Use the typical values below as a starting point, not for precise engineering calculations.
| Load Type | Typical PF | 1,380W at 24V (single-phase) |
|---|---|---|
| Resistive (heaters, incandescent) | 1 | 57.5 A |
| Fluorescent lamps | 0.95 | 60.53 A |
| LED lighting | 0.9 | 63.89 A |
| Synchronous motors | 0.9 | 63.89 A |
| Typical mixed loads | 0.85 | 67.65 A |
| Induction motors (full load) | 0.8 | 71.87 A |
| Computers (without PFC) | 0.65 | 88.46 A |
| Induction motors (no load) | 0.35 | 164.29 A |
Same Wattage, Other Voltages
Related Calculations
Other Wattages at 24V
| Watts | DC Amps | AC 1Φ Amps PF 0.85 |
|---|---|---|
| 400W | 16.67A | 19.61A |
| 450W | 18.75A | 22.06A |
| 500W | 20.83A | 24.51A |
| 600W | 25A | 29.41A |
| 700W | 29.17A | 34.31A |
| 750W | 31.25A | 36.76A |
| 800W | 33.33A | 39.22A |
| 900W | 37.5A | 44.12A |
| 1,000W | 41.67A | 49.02A |
| 1,100W | 45.83A | 53.92A |
| 1,200W | 50A | 58.82A |
| 1,300W | 54.17A | 63.73A |
| 1,400W | 58.33A | 68.63A |
| 1,500W | 62.5A | 73.53A |
| 1,600W | 66.67A | 78.43A |
| 1,700W | 70.83A | 83.33A |
| 1,800W | 75A | 88.24A |
| 1,900W | 79.17A | 93.14A |
| 2,000W | 83.33A | 98.04A |
| 2,200W | 91.67A | 107.84A |